8
The default date schedule is 01.
Door Unlock Schedule
Ref # [0011XX01YY06] where XX = module #, YY = door #
This schedule will determine when an access door will
be unlocked. When the door is unlocked, a user will not
require an access card to open the door. The door will
remain unlocked for the duration of the schedule.
Opening the door will not cause a door forced open event.
When the partition(s) to which the door zone is assigned
are armed, the door will automatically lock at the
beginning of the exit delay. If the Door Unlock schedule
becomes active while the partition(s) are armed, the door
will not unlock. However, if the partition is disarmed while
the door unlock schedule is active, the door will unlock,
and will remain unlocked until the scheduled end time.
NOTE:
If the door is assigned to more than one
partition, the door will only lock once the last partition
to be armed has begun its exit delay.
The default date schedule is 00 (disabled).
Request To Exit (REX) Schedule
Ref # [0011XX01YY07] where XX = module #, YY = door #
This schedule controls the Unlock on REX option. When
the schedule is active, tripping a Request To Exit device
will cause the door to unlock for the programmed Door
Unlock time (see section 3.5 “Door Times”). If the
schedule is not active, a Request To Exit will not cause
the door to unlock.
The default date schedule is 01.
Second Card Schedule
Ref # [0011XX01YY08] where XX = module #, YY = door #
This schedule will determine when users with the Wait
For Privilege option enabled will require a Privileged user
to grant them access to the area. If the Second Card
Schedule is active, the following will occur:
The user with the Wait For Privilege card presents their
card first. The LED on the card reader will flash slowly
for 10 seconds. If during this time a Privileged card is
used, the door will be unlocked. Only privileged cards
are capable of allowing access to the system. If a non-
privileged card is used, the door will not be unlocked
and a log will be made to the buffer. This feature is used
for monitoring the access of users on the system.
The default date schedule is 00 (disabled).
Disarm Request Schedule
Ref # [0011XX01YY09] where XX = module #, YY = door #
This schedule will program the times when the selected
partitions may be disarmed by a user presenting their
access card at the appropriate reader. Only partitions
which have the door’s zone assigned to them, and that
are selected in the arm/disarm mask will be affected.
To disarm the partition(s), the user must present their
access card and open the door. The partition(s) will be
disarmed if the Disarm Request schedule is active. If the
user presents their card is outside of the Disarm Request
schedule time window, the door will be unlocked but
the partition(s) will not be disarmed when the door is
opened. The user must then enter their access code at a
keypad to disarm the partition(s).
NOTE
: To disarm a partition or enter a partition which
is armed, the user must be assigned to the partition,
and the user’s disarm attribute must be enabled in
access code and card programming. See your PC4010/
4020 Instruction Manual for information on
programming access codes and cards.
The default date schedule is 00 (disabled).
Code Schedule
Ref # [0011XX01YY11] where XX = module #, YY = door #
When this schedule is active, the door will not unlock
until the card is presented AND a valid access code is
entered on the keypad. When the schedule is inactive,
the door will unlock when an access card is presented.
If Schedule [00] is programmed into this section, the door
will be unlocked by an access card only when the
partition(s) the door is assigned to are disarmed. When
the partitions are armed, an access code will also be
required.
NOTE
: The Code Required option must be enabled in
order for this feature to work.
The default date schedule is 01.
Forced Open Schedule
Ref # [0011XX01YY12] where XX = module #, YY = door #
When this schedule is active and a door is opened without
tripping a REX device, a Door Forced Open event will be
logged to the event buffer and transmitted to central
station. When the schedule is inactive and a door is forced
open, the event will be logged, but not transmitted.
NOTE
: In order for this option to work, the door must
be assigned a zone and that zone must be assigned to
one or more partitions.
The default date schedule is 00 (disabled).
Forced Open Bell Schedule
Ref # [0011XX01YY13] where XX = module #, YY = door #
When this schedule is active and a door is opened without
tripping a REX device, the partition(s) the door is assigned
to will go into alarm. The alarm will be on until the bell
cut-off time expires, or until an access code is entered to
silence the alarm.
NOTE
: In order for this option to work, the door must
be assigned a zone and that zone must be assigned to
one or more partitions.
The default date schedule is 00 (disabled).
Open Too Long Schedule
Ref # [0011XX01YY14] where XX = module #, YY = door #
When the schedule is active and the assigned door is left
open past the Door Open time, an Open Too Long event
will be logged to the event buffer and transmitted. When
the schedule is inactive and the door is left open past the
Door Open time, the event will be logged but not
transmitted. The Door Open time is default set at 30
seconds but can be changed (see Section 3.4 “Door
Times”).
