7
P r o g r a m m i n g t h e P C 4 8 2 0
NOTE:
This option can only be enabled for Door 1.
If disabled, doors 1 and 2 will have their own zone
and partition assignments. (Default = No)
3.3 Arming and Disarming with Access Cards
The PC4820 can be set up so that users may arm and
disarm, or postpone the autoarm of any active partition
on the system. To set up partitions to be armed and
disarmed from an access control module, the following
must be programed:
1. The user’s access card must be assigned to the
appropriate partition(s); an access level must be
assigned to the access card; and the access card must
have the arm and or disarm attribute enabled (see
section 3.8 “Programming Access Cards”).
2. The access door must be assigned a PC4010/4020
zone (see section 3.5 “Zone Assignment for Access
Doors”), and the zone must be assigned to the
appropriate partitions (see below).
3. The Arm/Disarm mask must be programmed to
include the partition(s) that are to be armed/
disarmed from that access card reader (see below).
4. The Postpone Arm, Arm Request and Disarm
Request schedules must be programmed with a date
schedule other than [00] (see section 3.6 “Access
Door Schedules”).
HINT
: When using the arming/disarming options of the
PC4820, the use of Bell Squawk and a Partition Status
output will allow for clear indication of the armed status
of the partition(s). These options can be enabled/disabled
on each partition (see your PC4010/4020 Installation
Manual for more information on programming partitions).
Arm/Disarm Partition Mask
Ref # [0011XX01YY01] where XX = module #; YY = door #
In this section select the partition(s) which users will be
able to arm and/or disarm when they present the
appropriate access card at the reader for the access door.
NOTE
: The zone assigned to the door must be assigned
to the same partitions selected in the Arm/Disarm
Partition Mask (Partition Programming, reference #
[0100XX03], where XX = partition #).
3.4 Door Times
Ref # [0011XX01YY02] where XX = module #; YY = door #
Door Unlock Time
The amount of time that the door will remain unlocked
after a valid access card has been presented is
programmed in this section. This is also the Request To
Exit time period. The default setting is 10 seconds. Valid
entries are from 001-255 seconds.
Door Open Time
This section will program the amount of time an access
door can remain open before a Door Open Too Long event
is generated. After half of the Door Open Time has
expired, the reader buzzer will pulse on and off as a
warning. At the end of the Door Open Time, the buzzer
will sound steady to indicate that the door has been left
open too long. The default setting is 030 seconds. Valid
entries are from 001-255 seconds.
3.5 Zone Assignment for Access Doors
Ref # [0011XX01YY03] where XX = module #; YY = door #
Assign each “door” to a zone on the PC4010/4020. Any
zone from Zone 17 to 128 may be used (Zone 9 to 64 on
the PC4010).
You can use any zone supervision option provided by
the PC4010/4020 for PC4820 zones. The end of line
resistors used for the door inputs are 5600
Ω
for the alarm
contact. If you will be using DEOL resistors, the tamper
contact is also 5600
Ω
.
The door’s zone must be programmed as a Standard
Delay, or an Auxiliary Delay zone (PC4010/4020
programming reference number [0100XX03], where
XX=partition number). See your PC4010/4020 v3.0
Installation Manual, section 5 “Zone Programming”.
3.6 Access Door Schedules
A date schedule can be assigned to each of the following
access door features. A date schedule will include the start
and end times for each event, the days of the week the
schedule will be active for and any holiday groups the
event will observe.
Date Schedules 00 and 01
If date schedule 00 is programmed, the feature will be
disabled (schedule is never active). If date schedule 01 is
programmed, the feature will be always on (schedule is
always active).
For more information regarding date schedule
programming, please refer to your PC4010/4020 v3.0
Installation Manual, section 14.1 “Date Schedules”.
There are 11 access door features which can be scheduled.
They are as follows:
Postpone Arm Schedule
Ref # [0011XX01YY04] where XX = module #, YY = door #
This schedule will program at what times the auto arming
sequence can be postponed by a user presenting their
access card at the appropriate reader. Only the partitions
to which the door ’s zone are assigned and that are
selected in the arm/disarm mask will be affected.
The user’s access card must also be assigned to the
appropriate partitions and have the disarming attribute
enabled for the feature to work correctly. See your
PC4010/4020 Instruction Manual for information on
programming access codes and cards.
The default date schedule is 01.
Arm Request Schedule
Ref # [0011XX01YY05] where XX = module #, YY = door #
This schedule will program when the selected partitions
may be armed by a user presenting their access card at
the appropriate reader. Only the partitions assigned to
the door zone and selected in the arm/disarm mask will
be affected.
The user’s access card must also be assigned to the
appropriate partitions and have the arming attribute
enabled in order for arming to occur. See your PC4010/
4020 Instruction Manual for information on
programming access codes and cards.
