background image

Fig 2. Powering an HS-EMS200 Thermostat with a Stand Alone Transformer

Fig 1. Wiring Diagram for One Heating/Cooling System with One HS-EMS200 Thermostat

Thermistor Temperature Sensor

HS-EMS200

W1

Y1

G

R

24V

24V(c)

CLK1

CLK2

RS2

RS1

RS+V

X1

X2

R/24V shunt. Remove if 
thermostat power is not 
supplied by equipment

Escort5580TC/

VPM5580TC

X

1

X

2

RS

+

V

X

2

X

1

RS

+

V

RS1

RS2

CLK1

CLK2

24V(c)

24V

R

G

W1

Y1

24V(c)

24V

G

W1

Y1

Heat Stage #1

Cool Stage #1

Fan

Power - Hot

Power - Common

Heating/Cooling 

System

HS-EMS200 

(Backplate)

Warning! Do not remove the internal jumper (shunt).

Output Terminal Functions

CLK1....................................Use with dry contact relay for alternate set points.
CLK2....................................Use with dry contact relay for alternate set points.
RS2 .......................................To Outdoor/Indoor remote sensors.
RS1 .......................................To Outdoor/Indoor remote sensors.
RS+V....................................To Outdoor/Indoor remote sensors and 

to Escort5580TC/VPM5580TC.

X2 .........................................To Escort5580TC/VPM5580TC.
X1 .........................................To Escort5580TC/VPM5580TC.

W1 ........................................Energizes on a call for first stage heating.
Y1 .........................................Energizes on a call for first stage cooling.
G ...........................................Fan is energized with a call for heating or 

cooling or by pressing the fan button.

R............................................Independent switching voltage.
24V .......................................24 V

AC

 Hot from equipment transformer.

24V(

C

) ..................................24 V

AC

 Common from equipment transformer.

Warning! Remove the internal jumper (shunt) before connecting the stand-alone transformer.

Escort5580TC/

VPM5580TC

X

1

X

2

RS

+V

X

2

X

1

RS

+V

RS1

RS2

CLK1

CLK2

24V(c)

24V

R

G

W1

Y1

24V(c)

24V

G

W1

Y1

Heat Stage #1

Cool Stage #1

Fan

Heating/Cooling 

System

HS-EMS200 

(Backplate)

Line Voltage

Common

Hot

24V

AC

Transformer

firealarmresources.com

Содержание HS-EMS200

Страница 1: ...backplate to mark the location of two mounting holes 4 Drill two 5 mm 3 16 mounting holes at the marked locations Tap the supplied nylon anchors flush to the wall and fasten the backplate using the supplied screws Do not over tighten 5 Connect the control wires to the thermostat as shown in the appropriate wiring diagram Push any slack wire back into wall Ensure that the wires are flush with the b...

Страница 2: ...tact relay for alternate set points RS2 To Outdoor Indoor remote sensors RS1 To Outdoor Indoor remote sensors RS V To Outdoor Indoor remote sensors and to Escort5580TC VPM5580TC X2 To Escort5580TC VPM5580TC X1 To Escort5580TC VPM5580TC W1 Energizes on a call for first stage heating Y1 Energizes on a call for first stage cooling G Fan is energized with a call for heating or cooling or by pressing t...

Страница 3: ...ticipated profits loss of time or any other losses incurred by the buyer in connection with the purchase installation operation or failure of this product WARNING DSC Ltd recommends that the entire system be completely tested on a regular basis However despite frequent testing and due to but not limited to criminal tampering or electrical disruption it is possible for this product to fail to perfo...

Страница 4: ...ally when the system is operating but there is no indication of this on the display To select continuous Fan operation press the FAN button and the display will show This is recommended for electronic air cleaners and continuous ventilation requirements Outdoor ODT Button When the outdoor temperature sensor option is connected to your thermo stat you can display the current outdoor temperature by ...

Отзывы: