manualshive.com logo in svg

Dryco Pool Cover Drain Kit, Руководство пользователя, Страница: 2 / 6

Поделиться
Скачать
Dryco Pool Cover Drain Kit Скачать руководство пользователя страница 2

Installation

Instructions for

Dryco Pool Cover

Drain Into Cover

Step 1: Find and mark the center

of the cover

Step 2: Position the rubber gasket on

top of the drain. The gasket has

alignment studs that fit into the drain

body

Step 3: Position the drain with

the silicone gasket under the

center of the cover.

Step 4: With the center punch,
find one of the 10 holes in the
drain body and puncture only
one hole through the cover.

Step 5: Position the rigid ring and
fiber gasket over the cover, aligning
the holes in the drain. Do not
completely tighten the screw down at
this time. This will allow the rigid ring
to pivot and line up with the other
screws.

Step 6: Align the rigid ring and
fiber gasket with the body of the
drain. Make sure that the cover
lays flat on the drain body and
gasket. Locate the screw hole on
the opposite side of the first
screw and puncture the cover for
the next screw.

Step 7: Insert the second screw.
Do not completely tighten the
screw this time.

Step 8:  Keeping the cover pulled tight
over the drain, punch the remaining
holes. Insert the remaining screws.

Step 9: Once all the screws are
installed, tighten them down.

Содержание Pool Cover Drain Kit







Отзывы:

Нет отзывов