Dru 0063CU3544, Руководство по установке

Страница: 13 / 36

English
INS T ALLAT I ON M A N U A L
!Caution
Do not ignite the appliance until it is fully installed.
Ø
Place the profile back in the appliance and fasten it with the self-tapping screws;
Ø
Place the vermiculite tray back in the appliance.
!Caution
Position the vermiculite tray correctly by means of the stop edges (as far as possible to the front).
5.10.2 Connecting the flue gas discharge system
In case of a newly to be constructed chimney breast (see section 5.7):
Ø
Connect the pipe pieces or the flexible stainless steel discharge pipe.
In case of an existing fireplace (see section 5.7):
In case of an existing fireplace plus chimney, the flexible stainless steel discharge pipe can be connected from the
inside:
Ø
Remove the self-tapping screws from the sealing plate and remove this plate from the appliance
(see Appendix 3, fig. 14);
Ø
Remove the self-tapping screws that are used to fasten the flue spigot and remove the flue spigot via the top of
the appliance (see Appendix 3, fig. 15);
Ø
Connect the flexible stainless steel discharge pipe to the flue spigot and place it back in the appliance with the
self-tapping screws;
Ø
Place the sealing plate back in the appliance and fasten it with the self-tapping screws.
5.11 Setting the appliance
The appliance has to be set in such a way that it works correctly in combination with the used concentric system.
!Caution
In case of a flue gas discharge system that is shorter than 6 metres, the restrictor in the flue spigot must be
adapted (see Appendix 2, tables 5 and 6):
Ø
Remove the restrictor from the flue spigot (see Appendix 3, fig. 16 (R));
Ø
Break both rings (A) from the restrictor by moving it back and forth until it comes off. A large passage will remain
(B);
!Caution
Do not deform the ring, the restrictor should be flat.
Ø
Place the restrictor back in the flue spigot.
5.12 Glass pane
Avoid damaging the pane during removal/placing.
5.12.1 Removing the glass pane
Observe the following actions to remove the glass pane (see Appendix 3, fig. 6 to 9):
Ø
Remove the lower decorative strip by grabbing it in the groove and lifting it out;
Ø
Remove the self-tapping screw of the vertical decorative strip and remove the decorative strip by tilting it
sideways at the top and lifting it out, do the same at the other side;
Ø
Remove the central self-tapping screw from the upper glass strip and remove the glass strip;
Ø
Tilt the glass pane from the top, away from the appliance;
!Caution
Prevent the glass pane from making an angle that is too large and could damage the glass pane.
Ø
Grab the glass pane at both sides and remove the glass pane;
Ø
Store the glass pane on a safe place.
5.12.2 Placing the glass pane
Ø
Place the glass pane at the bottom of the holders;
Ø
Tilt the glass pane from the top, against the appliance;
Ø
Place the central glass strip and fasten it in the middle by means of a self-tapping screw;
!Caution
Avoid/remove finger prints on the glass pane, as they will burn into the glass.
Ø
Place back the vertical decorative strips and fasten them with the self-tapping screws;
Ø
Place back the lower decorative strip.
5.13 Placing the wood set
The appliance is supplied with a wood set.
!Caution
The figures do not always show the correct colours.
13