DROPSA MiQueL Скачать руководство пользователя страница 12

12 

15. OPERATING HAZARDS 

 

Compliance with the essential safety requirements and the provisions specified in the machine directive was checked by 

filling out prepared check lists that are contained in the 

technical file

Two types of lists were used: 

 

Risk assessment (UNI EN ISO 14121-1). 

 

Compliance with the essential safety requirements Machine Directive –EC 06/42). 

The risks that were not completely eliminated, but considered acceptable, are specified below: 

 

During maintenance, sprays of oil at low pressure are possible (for this purpose, suitable PPE must be worn during 

maintenance activities). 

 

Electrocution: This can only occur in the case of serious user incompetence, but the user must be qualified. 

 

Unsuitable postures: The correct dimensions and installation methods are described in this manual. 

 

Use of unsuitable lubricant: The specifications of the lubricant are indicated both on the unit as well as in this 

User and 

maintenance manual

 (

in the case of doubt, contact the Dropsa S.p.A technical office

.). 

 

FLUIDS THAT ARE NOT PERMITTED 

FLUIDS 

RISKS 

Lubricants with abrasive additives. 

Wear of internal components. 

Lubricants with silicone additives. 

Seizure. 

Petrol – solvents – inflammable liquids. 

Fire – explosion – damage to the gaskets. 

Corrosive products. 

Corrosion - damage to people. 

Water. 

Unit oxidation. 

Food substances. 

They would be contaminated. 

 

Содержание MiQueL













Отзывы: