background image

5.7  

ELECTROPNEUMATIC 

CHANGE-OVER (optional)  

The pump can be equipped with a pneumatic change-over valve piloted by a hazardous area certified solenoid. 
 

 

 

 

 

 

 

 

 

 

 

 

 

 

5.8  HYDRAULIC CHANGE-OVER (optional)  

The  pump  can  also  be  equipped  with  a  hydraulic  change-
over valve that activates when the pressure is made on each 
line. 
Two pressure indicators are equipped with a pin that allows 
the operator to visualize the operation of the valve. 
The  valve  can  also  be  equipped  with  cycle  sensor  (certified 
for hazardous areas) to monitor the inversion phases of the 
valve.  
 
 
 
 
 
 
 
 
 
 

6. UNPACKING AND INSTALLATION 

 

6.1  UNPACKING 

Once the suitable location for installation has been identified, open the package and remove the pump. Check that it was not 
damaged during transport or storage. The packaging material does not require special disposal precautions as it is not in any 
way dangerous or polluting. Refer to the local regulations for disposal. 

 
6.2  INSTALLATION 

Pump assembly operations are not required. The pump is fixed on a metal pallet that permits safe handling with a transpallet or 
fork  lift  truck. The  pallet  was  designed  to be  installed  in  the  plant.  It  has  four  Ø  14  mm  holes  suitable  for  fixing  to  the  floor. 
Suitable  space  must  be  provided  (as  shown  in  the  installation  diagram)  to  prevent  abnormal  positions  or  the  possibility  of 
impacts. Then, as described above, the pump must be connected hydraulically to the machine and then the connection to the 
control panel must be made. 
 
 
 
 
 
 
 

 

 

  The main change-over parts are: 

 

A casing with a central lapped hole that makes it possible 
to make a dry seal connection with the inversion piston, 
which is facilitated by a balancing system; 

 

A  ground  piston  with  a  dual  coupling  surface,  with 
grooves  that  improve  lubrication  and  the  seal  at  high 
pressures; 

 

The inversion phase is facilitated by a balancing system; 

 

Sealing gaskets that can support high pressure levels, by 
means of a pressurized chamber, optimizing the change-
over  function; 

 

Two  single  acting  pneumatic  actuating  cylinders, 
controlled by an 5/ 2 type solenoid valve. 

 

 

Содержание Mini-SUMO






















Отзывы: