DriSteem ultra-sorb MP Скачать руководство пользователя

Страница: 4 / 32

ULTRA-SORB MODEL MP INSTALLATION, OPERATION, AND MAINTENANCE MANUAL

Ultra-sorb Model MP fi eld assembly

INSTALLATION

Note: These assembly instructions are for Ultra-sorb Model MP panels shipped

unassembled by request or as required. Panels with overall height more
than 98" (2490 mm) are shipped unassembled.

LAY OUT THE PANEL COMPONENTS

Place the panel components on a large, ﬂ at working surface.

ATTACH THE TOP FRAME ASSEMBLY

Span the ﬂ anges with the top frame assembly. Align the locating pins on the
ﬂ anges and top frame, and insert screws.

TIGHTEN THE FLANGE LOCKNUTS

Torque the eight ﬂ ange locknuts to 16 ft-lb (22 N-m) at 100 rpm maximum
using a 7/16" deep-well socket.

INSTALL THE DISPERSION TUBES

Note: Do not remove the poly ﬁ lm from the dispersion tubes until after the

panel is installed.

Table 2-1:
Ultra-sorb Model MP components

Component

Qty.

Header assembly

Dispersion tubes

Varies

Top frame assembly

Side ﬂ anges

Screws

Varies

Flange locknuts

Header
assembly

Flange
locknut

Left side
ﬂ ange

OM-7846

Top frame
assembly

Right side ﬂ ange

Insulation

FIGURE 2-1: ULTRA-SORB MODEL MP COMPONENTS

Dispersion
tube

Locating pins

Содержание ultra-sorb MP

































Результаты поиска

Содержание ultra-sorb MP

Отзывы:

Похожие инструкции для ultra-sorb MP

Бренды по названию

Популярные бренды

DriSteem ultra-sorb MP, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание ultra-sorb MP

Отзывы:

Похожие инструкции для ultra-sorb MP

Бренды по названию

Популярные бренды