background image

16

ULTRA-SORB MODEL MP INSTALLATION, OPERATION, AND MAINTENANCE MANUAL

Piping

 Table 16-2:
Steam loss of interconnecting steam hose or tubing

Description

Nominal hose or tubing size

Steam loss

Insulation thickness

Noninsulated

Insulated

inches

DN

lbs/hr/ft

kg/h/m

lbs/hr/ft

kg/h/m

inches

mm

Hose

40

0.15

0.22

N/A

N/A

N/A

N/A

2

50

0.20

0.30

N/A

N/A

N/A

N/A

Tubing

40

0.11

0.16

0.020

0.030

2.0

50

2

50

0.14

0.21

0.025

0.037

2.0

50

3

80

0.20

0.30

0.030

0.045

2.5

64

4

100

0.26

0.39

0.030

0.045

3.0

76

5

125

0.31

0.46

0.035

0.052

3.0

76

6

150

0.36

0.54

0.039

0.058

3.0

76

Note: Data based on an ambient air temperature of 80 °F (27 °C), fi berglass insulation, and copper tubing.

mc_051310_1216

Table 16-1:
 Maximum steam carrying capacity and length of interconnecting steam hose or tubing

Steam hose 

1

Copper or stainless steel tubing 

Hose I.D.

Maximum capacity 

Maximum length 

2

Tubing size

Maximum capacity 

3

 

Maximum developed 

length 

4

inches

DN

lbs/hr

kg/h

ft

m

inches

DN

lbs/hr

kg/h

ft

m

40

150

68

10

3

40

150

68

20

6

2

50

250

113

10

3

2

50

220

100

30

9

1.  Use DriSteem steam hose for best results. Other hose may have shorter 

life and may cause foaming in the evaporating chamber resulting in 
condensate discharge at the dispersion assembly. Do not use steam 
hose for outdoor applications.

2.  Maximum recommended length for steam hose is 10' (3 m). Longer 

distances can cause kinking or low spots.

80 

5

450

204

80

24

5

 100 

5

750

340

100

30

5

125 

5

1400

635

100

30

6

 5

150 

5

2300

1043

100

30

3. Insulate tubing to minimize loss of capacity and effi ciency. 
4.  Developed length of tubing equals measured length plus 50% of 

measured length, to account for fi ttings. 

   Longer tubing lengths are possible at capacities lower than listed 

maximums. Consult factory. 

5. Requires  fl ange connection.

Note:  Capacities and lengths in this table are for steam from a nonpressurized steam humidifi er to a nonpressurized steam dispersion panel, and are 

based on total maximum pressure drop in hose or tubing of 5" wc (1250 Pa).

mc_091410_1050-LVLH

INSTALLATION

Содержание ultra-sorb MP

































Отзывы: