DriSteem ultra-sorb MP Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 32

DriSteem ultra-sorb MP Скачать руководство пользователя страница 10

8

ULTRA-SORB MODEL MP INSTALLATION, OPERATION, AND MAINTENANCE MANUAL

Mounting and support

Elbow

Duct

Air ﬂ ow

Air ﬂ ow

Ultra-sorb

Ultra-sorb

Duct split

Ultra-sorb

Air ﬂ ow

Drip pan

Pipe to drain size as required

Ceiling line

Vapor absorption

area

* This length of duct should have sealed seams

and should be at least three times the height
of the Ultra-sorb panel.

OM-7862

Non-

wetting

distance

OM-198

2" (50 mm)

OM-197

Cold
air
ﬂ ow

Ultra-sorb

Extended trails of
fog may develop

High limit duct humidistat 10' to 15' (3 to 4.5 m)
downstream from Ultra-sorb

INSTALLATION

mc_101410_0955

mc_052411_0830

INSTALLATION IN A COLD AIR STREAM

When a humidiﬁ er is installed in a duct that will carry cold air, determine
the dew point temperature. If the psychrometric chart reveals that saturation
may occur, protection should be provided. A high-limit humidistat or humidity
transmitter can be used for this purpose. See Figure 8-1.

PLACEMENT UPSTREAM FROM AN ELBOW OR DUCT SPLIT

Installation upstream from elbows or duct splits can be done. See Figure
8-2 if placed upstream a minimum of the non-wetting distance.

INSTALLATION ABOVE VALUABLE EQUIPMENT

Water piping and humidiﬁ ers should not be installed above expensive
equipment. A condensing or leaking water pipe or other accidental water
spillage could damage the equipment below. When such an installation cannot
be avoided, install a drip pan under the humidiﬁ er piping, valve, etc. to catch
and drain away unintended water. See Figure 8-3.

PANEL SUPPORT

The duct or air handler section and Ultra-sorb panel must be properly
supported to carry the weight of the assembly. The weight of the piping must
be supported by the building structure rather than by the Ultra-sorb unit.
Excessive weight on the Ultra-sorb panel may stress the connections, causing
them to fracture and leak.

mc_071311_1540

FIGURE 8-1: INSTALLATION IN A COLD
AIR STREAM

FIGURE 8-2: UPSTREAM PLACEMENT

FIGURE 8-3: INSTALLATION ABOVE
VALUABLE EQUIPMENT

«
...
8
9
10
11
12
...
»

Содержание ultra-sorb MP

































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды