background image

Form No. TCI-W11-IOM-EN-1120

Part No. 89000

0--280

 

Rev A

DRI-STEEM Corporation

 

a subsidiary of Research Products Corporation 

DriSteem U.S. operations are ISO 9001:2015 

certified

U.S. Headquarters:

14949 Technology Drive

Eden Prairie, MN 55344

800-328-4447 or 952-949-2415

952-229-3200 (fax) 

© 2020 Research Products Corporation

Table 6-1:
Troubleshooting guide

Issue

Power failure

Check for proper supply voltage.
Check for wiring shorts; reset breaker.

Error message

Err1: 

An assigned input is not enabled or missing. All control loops, functions, 

and outputs tied to this input will be disabled. Verify input connections, jumper 

settings and parameter settings for the input involved.

Err3:

 A function refers to a disable input. Disable the function or enable the 

input.

Err4:

 Internal failure. Product must be replaced.

Table 6-2:
Replacement parts

Model

Description

Part Number

TCI-W11-U-W26 kit 1 Model TCI-W11-U-W26, 1 duct sensor

600968

TCI-W11-U-W26

PI-controller, wall flush mounted int. 1 UI, 1 AO, 

default: 0-10V input remote RH, 0-10V output 

humidify

600966

TCI-W11-U-H-W24

PI-controller, wall flush mounted int. 1 UI, 1 AO, 

int. humidity sensor 3% accuracy, default: humidity 

control, int. RH, 0-10V output

600965

Accessories

Duct sensor, 3% 0 - 10V

600967

AES1-HT-A2

RH sensor 2%

600983

AES1-HT-A3

RH sensor 3%

600982

Содержание TCI-W11-U







Отзывы: