DriSteem HUMIDI-TECH Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 32

background image

12

HUMIDI-TECH

®

DISPERSION

Installing Space Distribution Units
(SDUs)

Provide at least 150 mm clearance on each side of
the SDU.

Field wiring is required to connect the SDU fan and
airflow proving switch terminals to the respective
HUMIDI-TECH electrical panel terminals. Refer to
the external connections diagram in the package
shipped with your unit.

A HUMIDI-TECH with an SDU is a class-one-rated
assembly. It has been tested and is in compliance
with the requirements to be mounted in areas
accessible to the general public.

When performing HUMIDI-TECH
maintenance

If the SDU-E or SDU-I is installed immediately
above the HUMIDI-TECH, disconnect both hose
clamps on the steam hose, grip the hose and rotate
it to break it loose from the tubing, and then slide
the hose up onto the SDU steam tube until sufficient
clearance is provided to move the tank.

SDU-E mechanical detail

DC-1078

57 mm

DN40 or DN50
steam inlet

614 mm

Steam
outlet

472 mm

276 mm

57 mm

Front view

Side view

DN40 steam inlet

472 mm

614 mm

Air intake
grille

Humidified air
discharge grille

276 mm

SDU-I mechanical detail

Front view

Side view

DC-1076

409 mm

DN40 or DN50
steam inlet

409 mm

Note: Maximum ambient RH must not exceed
45% for the SDU-I to operate properly.

VM99-C-0302-M-0302.pdf 12

11/19/2009 9:51:08 AM

«
...
10
11
12
13
14
...
»

Содержание HUMIDI-TECH

































Отзывы:

Нет отзывов

Похожие инструкции для HUMIDI-TECH

Бренд: DanVex Страницы: 12

Бренд: Fagor Страницы: 54

Бренд: Dantherm Страницы: 72

Бренд: DriSteem Страницы: 6

Бренд: Vitek Страницы: 28

758.144108 Kenmore

Бренд: Sears Страницы: 17

Бренд: HANKISON Страницы: 48

Бренд: TCL Страницы: 42

Бренд: Fortress Technologies Страницы: 10

Soleus Air GL-DEH-30-1

Бренд: Gree Страницы: 16

Бренд: Black & Decker Страницы: 14

Бренд: Black & Decker Страницы: 16

Бренд: Black & Decker Страницы: 20

Бренд: Black & Decker Страницы: 88

Бренд: ALPATEC Страницы: 6

Lifesmart SC-D027

Бренд: Supply Chain Sources Страницы: 10

Бренд: Air-O-Swiss Страницы: 64

Бренд: Eberg Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды