manualshive.com logo in svg

Dresser MOONEY FLOWGRID SLAM SHUT, Инструкция по установке, эксплуатации и обслуживанию

Поделиться
Скачать
Dresser MOONEY FLOWGRID SLAM SHUT Скачать руководство пользователя страница 3

Mooney Controls
Dresser, Inc.
Salt Lake City, Utah

Slam Shut Sense

Under Pressure

Trip Control 

Valve

Over Pressure

Trip Control 

Valve

Filter

Type 30

Restrictor

Type 24

Pilot Sense

Pilot Series 20

Loading

Outlet

Inlet

Outlet

Vent Valve

Latched

Vent

Actuator

Flowgrid Regulator &

Integral Slam Shut Valve

Flapper Valve 

(Open Position )

Center Port

Flowgrid Slam Shut |  3

 Figure 4 – Slam Shut Nameplate

 Figure 5 –  Actuator & Latch Mechanism Open

Nameplate Information

 Flowgrid Nameplate information, see the Flowgrid IOM.

 5.  The Slam Shut Nameplate location.

6.  The Flowgrid Nameplate location.

7.  The flow direction is marked on the spring case or cover 

(“INLET” and/or a flow arrow). Proper alignment assures 
that the diaphragm guide on the Spring Case is aligned 
toward outlet side of the regulator.

8.  The % Capacity tag indicates the capacity of the throttle 

plate (100%, 75%, 50%, & 35%) in the valve. 

 

NOTE: On all 2” standard port valves the throttle plate 
itself is stamped. This tag is not installed on stand 
alone Slam Shuts.

9.  Over pressure spring range nameplate. The factory 

marks the nameplate to indicate which spring is installed 
during manufacture. If the spring is changed make sure 
to note it on the nameplate.

10.  Under pressure spring range nameplate. The factory 

marks the nameplate to indicate which spring is installed 
during manufacture. If the spring is changed make sure 
to note it on the nameplate.

Item

Definition

NITRILE

The Slam Shut has all nitrile soft 
goods.

VITON

The Slam Shut has nitrile static 
seals and viton dynamic seals and 
diaphragms.

MAX INLET

Maximum inlet pressure psig/bar

MIN DIFF

Minimum difference in inlet and 
downstream pressure required for 
the Slam Shut to operate. 

OP. TEMP.

Operation Temperature range

 Principal of Operation

During normal operation the latch mechanism holds the 
closure element (flapper) open as shown in Figure 5. The 
sense or downstream pressure is monitored by the high and/
or low trip controller diaphragms. The controller diaphragms 
convert the sense pressure into a force proportional to the 

pressure. The force produced by the controller diaphragm is 
counter balanced by the set point adjustment spring located 
in the spring case. The adjusting screw is used to vary the 
spring force and control the over pressure set point or the 
under pressure set point. 

Содержание MOONEY FLOWGRID SLAM SHUT





















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды