background image

Preparation

1. Prior to installation, examine all boxes and packages for shipping damage and compare the piece 

count with your packing slip. After opening all boxes and packages read this introduction carefully. 

Check that all of the needed parts are included in the package by checking off the components on 

the “Detailed Diagram of Shower Door Components”. If the unit has been damaged, has a finishing 

defect, or has missing parts, please contact our customer support department within 3 business 

days of the delivery date. Please note that DreamLine

®

 will not replace any damaged products 

or missing parts free of charge after 3 business days or if the product has been installed. Feel 

free to contact DreamLine

®

 if you have any questions, and please provide an order number, job 

name or other proof of purchase to help us identify your original order.

2. Please note that you should consult your local building codes with questions on installation 

compliance standards. Building and plumbing codes may vary by location, and DreamLine

®

 is not 

responsible for code compliance standards for your project and will not accept any returns.

3. If this unit is going to be installed in a new construction, please install all of the required plumbing 

and drainage before installing the shower. Use a competent and licensed (if required by local code) 

plumber for all plumbing installation

4. Please make sure that prior to beginning the installation, the surfaces are leveled and solid and 

will be able to support the total weight of the unit. Also make sure the walls are at right angles. 

Irregular installation surface level, radius corners or improper angle of side walls will result in serious 

problems for your installation. Please, note that some adjustments and drilling might be necessary 

during the installation process. 

5. Please protect all primary surfaces of the product during installation. Never set your glass down 

directly onto a tile floor. Leave corner protectors in place until necessary to remove them. Always 

use a piece of wood or cardboard to protect the bottom edge and corners of the glass prior to and      

during installation. 

6. This unit must be installed upon a finished threshold and against finished walls.

7.

 This model can be adjusted up to 3/8” on the panel side for out-of-plumb conditions. Verify that 

your walls are plumb before proceeding with the installation.

   

8. This model requires that you drill into the threshold for proper installation

9. This model is available in either a shower height or a tub height. This manual will describe the 

steps showing a shower height model. Please follow the same sequence of installation steps for the 

tub height installation.

 

10. This model requires two installers.

11. This model is available with either a LEFT or RIGHT hand L-Bracket for support. Please be 

certain that you have ordered the correct model for your application prior to installation.

NOTE:  This manual will describe the shower door installation using a LEFT handed L-Bracket. 

For the Right handed L-Bracket installation, simply begin your installation on the opposite wall and 

reverse the orientation of the parts as necessary.

2

MIRAGE-X manual Ver 1 Rev 1  12/2015

Содержание MIRAGE-X SHDR-1948723L Series























Отзывы: