background image

15 

-

 

 

-

 

The recommended operating pressure in the hot water circuit is 0.48 MPa. At the hot water discharge 
we recommend that a reverse flap and an expansion tank are installed (at least 4% of hot water 
volume in the manifold) to eliminate reverse pressure shocks.

 

 
 

Both the electric and water installation must follow and meet the requirements 

and regulations relevant in the country of use!

 

 

 

4.2

 

TRANSPORT & STORAGE 

INSTRUCTIONS 

The device shall be transported and stored in dry place and protected from

 

weather effects with temperature 

range from 

-

15 to +50°C. During loading and unloading the instructions stated on the packaging shall be 

observed.

 

 

4.3

 

DISPOSAL OF PACKAGING MATERIAL AND NON-
FUNCTIONING PRODUCT 

The  packaging  that  the  product was  delivered  in

 

has  been  paid  for  in  form of

 

a  service  fee  for the  provision of the  return  and recovery.  The  packaging  that

 

the  product  was  delivered  in  has  been  paid  for  in  form  of  a  service  fee  for

 

the  provision  of  the  return  and  recovery.  Take  the  water  heater  packaging

 

to  a  waste  disposal  place  determined  by  the  municipality.  Disassemble

 

the  discarded  and  unserviceable  product  after  the  operation  terminates,

 

and  transport  it  to  a  waste  recycling  centre  (collecting  yard),  or  contact

 

the manufacturer.

 

 

5

 

PRODUCT ACCESSORIES 

The product is supplied together with a safety valve. Safety valve is packed and placed in the upper section 
of the heater’s packaging.

 

 

It is in your own interest to check the completeness of the accessories. 

 
 

2

-

10

-

2018

 

Содержание OKHE ONE20
















Отзывы: