Draytek VigorSwitch G2240 Скачать руководство пользователя страница 95

Страница: 95 / 156

VigorSwitch G2240 User’s Guide

Action:

Range: Permit / Deny

Permit: Permit the met ACL ingress classification rule
packets forwarding to other ports on the switch
Deny: Discard the met ACL ingress classification rule
packets

Rate Limiter

: Range: Disabled / 1-16

Disable: Disable Rate Limiter function
1-16: Apply the Rate Limiter Number setting for met ACL
ingress rule packets

Port Copy:

Range: Disabled / 1-24

Disable: Disable the Port Copy function
1-24: The packets will be copied to the selected port when
they met ACL ingress rule.

Function name:

Wizard

Function description:

The wizard function provides 4 type of typical application for user easy to configure their
application with ACL function.

Parameter description:

Please select an Action:

Set up Policy Rules / Set up Port Policies / Set up Typical
Network Application Rules.

Click on <Next> to confirm current setting and go to next
step automatically.

Содержание VigorSwitch G2240




























































































































































Результаты поиска

Содержание VigorSwitch G2240

Отзывы:

Draytek VigorSwitch G2240, Руководство пользователя, Страница: 95 / 156

Результаты поиска

Содержание VigorSwitch G2240

Отзывы: