Draytek VigorSwitch G2240 Скачать руководство пользователя страница 58

Страница: 58 / 156

VigorSwitch G2240 User’s Guide

Parameter description:

Aging Time:

Delete a MAC address idling for a period of time from the
MAC Table, which will not affect static MAC address.
Range of MAC Address Aging Time is 10-1000000 seconds.
The default Aging Time is 300 seconds.

Disable automatic aging:

Stop the MAC table aging timer, the learned MAC address
will not age out automatically

Auto:

Enable this port MAC address dynamic learning mechanism.

Disable:

Disable this port MAC address dynamic learning mechanism,

only support static MAC address setting.

Secure:

Disable this port MAC address dynamic learning mechanism
and copy the dynamic learning packets to CPU

Save:

Save MAC Address Table configuration

Reset:

Reset MAC Address Table configuration

Содержание VigorSwitch G2240




























































































































































Результаты поиска

Содержание VigorSwitch G2240

Отзывы:

Draytek VigorSwitch G2240, Руководство пользователя, Страница: 58 / 156

Результаты поиска

Содержание VigorSwitch G2240

Отзывы: