Draper Premier XL 220 Скачать руководство пользователя страница 4

Section 6 -

 Limit Adjustments 

(Standard Motor)

Please Note:

 Screen limits are factory set for optimum performance of screen. Any adjustment of these limits could void warranty.  Please check with Draper prior to 

resetting screen limits.

CAUTION:

 Always be prepared to shut screen off manually when new adjustment is being tested. Screen may be severely damaged if viewing surface is allowed to run 

too far up or too far down.

CAUTION:

 Be sure all switches are in “off” position before adjusting limit switches.

1. 

Adjusting “fully up” position —If you do, however, “Up” stopping position may be adjusted by turning yellow limit switch adjustment socket. The yellow socket is located on left end 

of screen roller and is accessible to a screwdriver/Allen wrench 

(4mm or 

5

/

32

")

. Turning socket counterclockwise will allow viewing surface to retract farther into case. Turning it 

clockwise will cause surface to stop farther out of case. One full revolution of socket will alter stopping position of viewing surface by approximately 38.1mm.

2. 

Adjusting “fully down” position — “Down” stopping position may be adjusted by turning white limit switch adjustment socket. The white socket is located on left end of screen roller 

and is accessible to a screwdriver/Allen wrench 

(4mm or 

5

/

32

")

. Turning socket counterclockwise will allow viewing surface to run farther down. Turning it clockwise will shorten 

viewing surface, causing it to stop in a less extended position. At no time should viewing surface be unrolled enough to expose any part of screen roller.

Section 5 -

 Limit Adjustments 

(Motor with Internal Low Voltage Controller)

Please Note:

 Screen limits are factory set for optimum performance of screen. Any adjustment of these limits 

could void warranty.  Please check with Draper prior to resetting screen limits.

CAUTION:

 Always be prepared to shut screen off manually when new adjustment is being tested. Screen 

may be severely damaged if viewing surface is allowed to run too far up or too far down.

CAUTION:

 Be sure all switches are in “off” position before adjusting limit switches.

(Height adjustments are 

made from wall switch)

1. 

Connect ILT switch to motor via terminal blocks, or via modular port using four conductor modular cable. When using 

modular cable, cable connectors MUST NOT be crimped in reverse, as with standard telephone cable.

2. 

Set slide switch to lower position. Press and hold DOWN button on switch to move viewing surface to desired lower 

limit. If screen moves in opposite direction, release DOWN button and press and hold down STOP button for four 

seconds. This will reverse operation of UP and DOWN switches.

3. 

Move slider switch into center position. Wait a couple of seconds.

Please Note:

 Moving slider switch from down to up in one motion sets two limits in same position.

4. 

Set slide switch to higher position. Move viewing surface to desired upper limit by pressing and holding UP button on 

wall switch. 

5. 

Return slide switch to center position to return to normal operation.

POSITION

FUNCTION

DOWN

UP

CENTER

Set LOWER limit

Set UPPER limit

Normal Operation

To Motor

with

Internal

Low Voltage

Slide

Switch

Back View of Wall Switch

U

p

D

o

w

n

C

o

m

m

o

n

+

5V

DC

To Motor

with

Internal

Low Voltage

Please Note:

 5V DC must be 

connected in order to set 

limits using wall switch.

page 4 of 7

Premier XL

® 

/

 

Targa XL

® 

220V

Electric Projection Screen

Содержание Premier XL 220








Отзывы: