manualshive.com logo in svg

Draper 94803, Руководство пользователя

Поделиться
Скачать
Draper 94803 Скачать руководство пользователя страница 15

9. SETTING 

THE 

DRILL

6. TECHNICAL 

DESCRIPTION

 Motor.

 Pulley 

cover.

 Guard.

  Plunge handle assembly.

 Geared 

chuck.

 Work 

table.

 Rack.

 Column.

 Base.

  No-volt on/off switch.

  Table height crank handle.

- 10 -

- 15 -

6.1 IDENTIFICATION 

FIG.9

FIG.10

NOTE:

 Remove the plug from the socket before 

carrying out adjustment, servicing or maintenance.

9.1  SPINDLE SPEED ADJUSTMENT 

FIGS. 9 - 10

This drilling machine is equipped with 12 drilling speeds.
 Remove the pulley cover securing screw.
 Select the speed most suitable for the intended 

application

†

.

 Loosen both the locking knobs and adjust the motor 

tension lever releasing the tautness across the drive 
belts.

 Move the belt to the corresponding sections of the 

motor, intermediate and spindle pulleys ensuring the 
belts remain horizontal.

 Apply pressure to the motor tension lever to tension 

the drive belt. With the correct tension achieved. 
Tighten both locking knobs.

 Gently lower the pulley cover before tightening pulley 

cover securing screw.

 Never attempt to operate the drilling machine with the 

pulley cover open or not fully secured.

CAUTION:

 Over tensioning the drive belt will 

accelerate belt wear, increase the loading on drive 
bearings and the motor possibly leading to premature 
failure. Under tensioning the drive belt will lead to the 
drive belt slipping and increased noise.

 

†

As a general rule material with a softer composition 

can be drilled faster as they cut more easily. Harder 
materials require a slower speed as attempting to 
make the hole at a high speed will result in the drill bit 
over heating which may result in a poorly finished hole, 
the bit annealing or the bit breaking.

 Drilling wood too slowly can cause splintering.

MOTOR

PULLEY

INTERMEDIATE

PULLEY

SPINDLE

PULLEY

A

B

C

D

1

2

3

4

1

2

3

4

Slow
1

Fast

12

Setting

1

2

3

4

5

6

7

8

9

10

11

12

Speed

230 min

-1

330 min

-1

370 min

-1

460 min

-1

530 min

-1

580 min

-1

1,030 min

-1

1,160 min

-1

1,280 min

-1

1,600 min

-1

1,790 min

-1

2,470 min

-1

Drive Belt Position

Spindle

A - 1

B - 2

A - 1

C - 3

B - 2

A - 1

D - 4

C - 3

B - 2

D - 4

C - 3

D - 4

Motor

4 - 4

4 - 4

3 - 3

4 - 4

3 - 3

2 - 2

3 - 3

2 - 2

1 - 1

2 - 2

1 - 1

1 - 1

Содержание 94803

























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды