background image

CONTACT US AT 

www.DRpower.com

          5

 

Never overlook the hazards of electricity.  Always follow these precautions: 

 

Never open the switch box or motor cover.  Never attempt any electrical repairs yourself.  If in doubt, consult a qualified 
electrician, visit our website at www.DRpower.com or contact DR Power Equipment for toll-free support at: 1-800-dr-owner 
(376-9637) for help or information. 

 

Never use an extension cord that is not rated for outdoor use. 

 

Never operate the Log Splitter if there is an electrical hazard present. 

 

Never operate the Log Splitter in wet conditions and always store under cover. 

 

Never operate the Log Splitter with a damaged electrical cord or damaged extension cord. 

 

Never pull on the electrical cord to move the machine. 

 

Always grasp the electrical cord plug when unplugging the cord from the outlet; never pull the plug out by the cord.  Make 
sure your fingers do not touch the metal prongs when plugging or unplugging. 

 

Never operate the Log Splitter unless the electrical cord is plugged into a properly grounded GFCI protected electrical outlet, 
which supplies 110-120v power, and is protected by a 20-amp circuit breaker. 

 

Never tamper with safety devices.  Check their proper operation regularly. 

 

If you are using an extension cord, keep the connection between the electrical cord and the extension cord well away from any 
water. 

 

Never use an extension cord longer than 25 feet and smaller than 12 awg in diameter, or longer than 50 feet and smaller than 
10 awg in diameter; the cord will produce a voltage drop that will prevent the motor from supplying full power and may cause 
damage to the motor. Use of a smaller diameter (larger awg number) extension cord could result in melting of the insulation 
or even create a fire. 

 

Always keep the electrical cord and/or extension cord away from excessive heat, oil, and sharp objects. 

 

Never tamper with the engine’s governor setting.  The governor controls the maximum safe operation speed and protects the 
engine.  Over-speeding the engine is dangerous and will cause damage to the engine and to the other moving parts of the 
machine.  If required, see your authorized dealer for engine governor adjustments. 

 

Keep combustible substances away from the engine when it is hot. 

 

Never cover the machine while the muffler is still hot. 

 

Do not operate the engine with the air cleaner or the carburetor air intake cover removed.  Removal of such parts could create 
a fire hazard.  Do not use flammable solutions to clean the air filter. 

 

The muffler and engine become very hot and can cause a severe burn; do not touch. 

Safety with Gasoline - Powered Machines (continued) 

Safety with Electric - Powered Machines 

Towing 

 

ALWAYS check before towing to make certain your Splitter is correctly and securely attached to the machine you are towing 
with. 

 

ALWAYS allow for added length of the Splitter behind you when turning, parking and in all towing situations. 

 

ALWAYS be careful when backing up. You could jackknife your Splitter if care is not taken. 

 

NEVER exceed 3 mph. when towing your Splitter. 

 

NEVER allow anyone to sit or ride on your Splitter. 

 

NEVER carry any cargo on your Splitter. 

 

Do travel slowly over rough terrain, on hillsides, and around curves to prevent tipping. 

 

Do not tow the Splitter near the edge of a ditch or excavation. 

Содержание PREMIER RAPIDFIRE

































Отзывы: