Dover Wilden Original PV20 Скачать руководство пользователя страница 3

Страница: 3 / 25

TT5049 EOM-PV20M 9/05

WILDEN PUMP & ENGINEERING, LLC

CAUTION:

Do not apply compressed air to the

exhaust port — pump will not function.

CAUTION:

Do not over-lubricate air supply —

excess lubrication will reduce pump performance.
Pump is pre-lubed.

TEMPERATURE LIMITS:

Neoprene

–18°C to 93°C

0°F to 200°F

Buna-N

–12°C to 82°C

10°F to 180°F

Nordel

–51°C to 138°C

–60°F to 280°F

Viton

–40°C to 177°C

–40°F to 350°F

Sanifl ex™

–29°C to 104°C

–20°F to 220°F

Polytetrafl uoroethylene (PTFE)

4°C to 104°C

40°F to 220°F

Polyurethane –12°C to 66°C

10°F to 150°F

Wil-Flex™

-40°C to 107.2°C -40ºF to 225ºF

NOTE: Not all materials are available for all
models. Refer to Section 2 for material options
for your pump.

CAUTION:

When choosing pump materials, be

sure to check the temperature limits for all wetted
components. Example: Viton

has a maximum

limit of 177°C (350°F) but polypropylene has a
maximum limit of only 79°C (175°F).

CAUTION:

Maximum temperature limits are

based upon mechanical stress only. Certain
chemicals will signifi cantly reduce maximum
safe operating temperatures. Consult Chemical
Resistance Guide (E4) for chemical compatibility
and temperature limits.

WARNING:

Prevention of static sparking — If

static sparking occurs, fi re or explosion could
result. Pump, valves, and containers must be
grounded to a proper grounding point when
handling fl ammable

uids and whenever

discharge of static electricity is a hazard.

CAUTION:

Do not exceed 8.6 bar (125 psig) air

supply pressure.

CAUTION:

The process fl uid and cleaning fl uids

must be chemically compatible with all wetted
pump components. Consult Chemical Resistance
Guide (E4).

CAUTION:

Do not exceed 82°C (180°F) air inlet

temperature for Pro-Flo V™ models.

CAUTION:

Pumps should be thoroughly fl ushed

before installing into process lines. FDA and
USDA approved pumps should be cleaned and/
or sanitized before being used.

CAUTION:

Always wear safety glasses when

operating pump. If diaphragm rupture occurs,
material being pumped may be forced out air
exhaust.

CAUTION:

Before any maintenance or repair is

attempted, the compressed air line to the pump
should be disconnected and all air pressure
allowed to bleed from pump. Disconnect all
intake, discharge and air lines. Drain the pump
by turning it upside down and allowing any fl uid
to fl ow into a suitable container.

CAUTION:

Blow out air line for 10 to 20 seconds

before attaching to pump to make sure all pipeline
debris is clear. Use an in-line air fi lter. A 5µ (micron)
air fi lter is recommended.

NOTE:

When installing Tefl on

diaphragms, it is

important to tighten outer pistons simultaneously
(turning in opposite directions) to ensure tight fi t.
(See torque specifi cations in Section 7.)

NOTE:

Cast Iron Tefl on

-fi

tted pumps come

standard from the factory with expanded Tefl on

gaskets installed in the diaphragm bead of the
liquid chamber. Tefl on

gaskets cannot be re-

used. Consult PS-TG for installation instructions
during reassembly.

This excludes Pro-Flo

P200

Advanced™ metal pumps.

NOTE:

Before starting disassembly, mark a line

from each liquid chamber to its corresponding air
chamber. This line will assist in proper alignment
during reassembly.

CAUTION:

Pro-Flo

pumps cannot be used in

submersible applications. Pro-Flo V™ is available
in both submersible and non-submersible options.
Do not use non-submersible Pro-Flo V™ models
in submersible applications. Turbo-Flo

pumps

can also be used in submersible applications.

CAUTION:

Tighten all hardware prior to installation.

S e c t i o n 1

C A U T I O N S — R E A D F I R S T !