Dover Wilden Advanced P400, Инженерия, эксплуатация и обслуживание

Страница: 29 / 56

P E R F O R M A N C E
PX400 Performance 27 WILDEN PUMP & ENGINEERING, LLC
SET
TING 4 PERFORMANCE CUR
VE
EMS CUR
VE
PX40
0 S
TAINLESS S
TEEL – UL
TRA
-FLEX™
EXAMPLE
A PX400 stainless steel, Ultra-Flex-fitted pump operating at EMS setting
4,
achieved
a
flow
rate
of
125
lpm
(33
gpm)
using
70
Nm
3
/h
(41 scfm) of air when run at 4.1 bar (60 psig) air inlet pressure and 2.8 bar (40 psig) discharge pressure (see dot on performance curve). The end user did not require that much flow and wanted to reduce air consumption at his facility
. He determined that EMS setting 3
would meet his needs. At 2.8 bar (40 psig) discharge pressure and EMS
setting
3,
the
flow
X
factor
is
0.89
and
the
air
X
factor
is
0.73
(see dots on EMS curve). Multiplying the original setting 4 values by the X factors provides the setting 3 flow rate of 111 lpm (29 gpm) and an air consumption of 51 Nm
3
/h (30 scfm). The flow rate was reduced by 11% while
the air consumption was reduced by 27%, thus providing increased efficiency
.
For a detailed example for how to set your EMS, see beginning of performance curve section. Caution: Do not exceed 8.6 bar (125 psig) air supply pressure
.
The Efficiency Management System (EMS) can be used to optimize the performance of your Wilden pump for specific applications. The pump is delivered with the EMS adjusted to setting 4, which allows maximum flow
.
The
EMS
curve
allows
the
pump
user to
deter
-
mine flow and air consumption at each EMS setting. For any EMS setting and discharge pressure, the X factor is used as a multiplier with the original values from the setting 4 per
-
formance curve to calculate the actual flow and air consumption values for that specific EMS setting.
NOTE: Y
ou can interpolate be
-
tween the setting curves for operation at in
-
termediate EMS settings.
TECHNIC
AL D
A
TA
Height
..........................
528 mm (20.8”)
Width
...........................
384 mm (15.1”)
Depth
...........................
310 mm (12.2”)
Ship W
eight
......
316 Stainless Steel 43 kg (94 lb)
Alloy C 45 kg (100 lb)
Air Inlet
..........................
19 mm (3/4”)
Inlet
. . . . . . . . . . . . . . . . . . . . . . . . . . . .
38 mm (1-1/2”)
Outlet
...........................
38 mm (1-1/2”)
Suction Lift
.....................
5.9 m Dry (19.3’)
9.0 m W
et (29.5’)
Disp. Per Stroke
.................
0.6 L (0.17 gal)
1
Max. Flow Rate
................
254 lpm (67 gpm)
Max. Size Solids
.................
4.8 mm (3/16”)
1
Displacement per stroke was calculated at 4.8 bar (70 psig) air inlet pressure against a 2.1 bar (30 psig)head pressure.
p E r F o r m a n c E
PX400 Performance 29 WILDEN PUMP & ENGINEERING, LLC
s
E
TT
iNg 4 PERFORMANCE CuR
vE
EMs CuR
vE
The Efficiency Management System (EMS) can be used to optimize the performance of your Wilden pump for specific applications. The pump is delivered with the EMS adjusted to setting 4, which allows maximum flow
.
PX40
0 S
TAINLESS S
TEEL – UL
TRA
-FLEX™
EXAMPLE
A PX400 metal, Ultra-Flex-fitted pump operating at EMS setting 4, achieved a flow rate of 231 lpm (61 gpm) using 102 Nm
3
/h (60 scfm)
of air
when
run at 4.1 bar
(60 psig) air inlet pressure and 0.7 bar (10
psig) discharge pressure (See dot on performance curve). The end user did not require that much flow and wanted to reduce air consumption at his facility
. He determined that EMS setting 2
would meet his needs. At 0.7 bar (10 psig) discharge pressure and EMS setting 2, the flow “X factor” is 0.81 and the air “X factor” is 0.47 (see dots on EMS curve). Multiplying the original setting 4 values by the “X factors” provides the setting 2 flow rate of 187 lpm (49 gpm) and an air consumption of 48 Nm
3
/h (28 scfm). The flow rate was reduced by 19% while
the air consumption was reduced by 53%, thus providing increased efficiency
.
For a detailed example for how to set your E
ms
, see beginning of
performance curve section. caution: Do not exceed 8.6 bar (125 psig) air supply pressure
.
The Efficiency Management System (EMS) can be used to optimize the performance of your Wilden pump for specific applications. The pump is delivered with the EMS adjusted to setting 4, which allows maximum flow
.
The EMS curve allows the pump user
to deter
-
mine flow and air consumption at each EMS setting. For any EMS setting and discharge pressure, the “X
factor” is used as
a multi
-
plier with the original values from the setting 4 performance curve to calculate the actual flow and air consumption values for that spe
-
cific EMS setting. Note: you can interpolate between the setting curves for operation at intermediate EMS settings.
TECHNIC
AL D
A
TA
Height
..........................
528 mm (20.8”)
Width
...........................
384 mm (15.1”)
Depth
...........................
310 mm (12.2”)
Ship W
eight
....
316 Stainless Steel 43 kg (94 lbs.)
. . . . . . . . . . . . . . . . . . . . . . . .
Alloy C 45 kg (100 lbs.)
Air Inlet
..........................
19 mm (3/4”)
Inlet
. . . . . . . . . . . . . . . . . . . . . . . . . . . .
38 mm (1-1/2”)
Outlet
...........................
38 mm (1-1/2”)
Suction Lift
.....................
6.2 m Dry (20.4’)
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9.3 m W
et (30.6’)
Disp. Per Stroke
................
0.76 l (0.20 gal.)
1
Max. Flow Rate
................
295 lpm (78 gpm)
Max. Size Solids
.................
4.8 mm (3/16”)
1
Displacement per stroke was calculated at 4.8 bar (70 psig) air inlet pressure against a 2 bar (30 psig)head pressure.
P E R f o R M A n C E
PX400 Performance 29 WILDEn PUMP & EngInEERIng, LLC
s
E
TT
iN
g
4 P
ER
FO
RM
ANC
E
C
uR
vE
EM
s C
uR
vE
PX40
0 S
TA
INLE
SS S
TEEL
– U
LT
RA
-F
LE
X™
E
XAMP
LE
A PX400 stainless steel, Ultra-Flex-fitted pump operating at E
ms
setting 4, achieved a flow rate of 125 lpm (33 gpm) using 70 Nm3/h (41 scfm) of air when run at 4.1 bar (60 psig) air inlet pressure and 2.8 bar (40 psig) discharge pressure (see dot on performance curve). The end user did not require that much flow and wanted to reduce air consumption at his facility
. He determined that E
ms
setting 3
would meet his needs. At 2.8 bar (40 psig) discharge pressure and Ems
setting 3, the flow “X factor” is 0.89 and the air “X factor” is
0.73 (see dots on Ems curve). m
ultiplying the original setting 4 values by the “X factors” provides
the setting 3 flow rate of 111 lpm (29 gpm) and an air consumption of 51 Nm3/h (30 scfm). The flow rate was reduced by 11% while the air consumption was reduced by 27%, thus providing increased efficiency
.
for a detailed example for how to set your EM
s, see beginning of
performance curve section. Caution: do not exceed 8.6 bar (125 psig) air supply pressure
.
The Efficiency management system (E
ms
)
can be used to optimize the performance of your Wilden pump for specific applications. The pump is delivered with the E
ms
adjusted
to setting 4, which allows maximum flow
.
The E
ms
curve allows the pump
user to deter
-
mine flow and air consumption at each E
ms
setting. For any E
ms
setting and discharge
pressure, the “X
factor” is used
as a
multi
-
plier with the original values from the setting 4 performance curve to calculate the actual flow and air consumption values for that spe
-
cific E
ms
setting. Note: you can interpolate
between the setting curves for operation at intermediate Ems settings.
TEC
H
NIC
A
L DA
TA
Height
..........................
528 mm (20.8”)
Width
...........................
384 mm (15.1”)
Depth
...........................
310 mm (12.2”)
ship W
eight 316 stainless steel
..
43 kg (94 lbs.)
. . . . . . . . . . . . . . . . . . . . . . . .
Alloy C 45 kg (100 lbs.)
Air Inlet
..........................
19 mm (3/4”)
Inlet
. . . . . . . . . . . . . . . . . . . . . . . . . . . .
38 mm (1-1/2”)
Outlet
...........................
38 mm (1-1/2”)
suction Lift
.....................
5.9 m Dry (19.3’)
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9.0 m W
et (29.5’)
Disp. Per stroke
.................
0.6 l (0.17 gal.)
1
max. Flow Rate
................
254 lpm (67 gpm)
max. size solids
.................
4.8 mm (3/16”)
1
Displacement per stroke was calculated at 4.8 bar (70 psig) air inlet pressure against a 2 bar (30 psig)head pressure.