Dover Wilden Advanced P400, Инженерия, эксплуатация и обслуживание

Страница: 23 / 56

P E R F O R M A N C E
PX400 Performance 21 WILDEN PUMP & ENGINEERING, LLC
SET
TING 4 PERFORMANCE CUR
VE
EMS CUR
VE
PX40
0
ALUMINUM – FULL
-S
TROKE PTFE-FITTED
TECHNIC
AL D
A
TA
Height
..........................
594 mm (23.4”)
Width
...........................
343 mm (13.5”)
Depth
...........................
310 mm (12.2”)
Ship W
eight
..............
Aluminum 33 kg (72 lb)
Air Inlet
..........................
19 mm (3/4”)
Inlet
. . . . . . . . . . . . . . . . . . . . . . . . . . . .
38 mm (1-1/2”)
Outlet
...........................
38 mm (1-1/2”)
Suction Lift
.....................
5.7m Dry (18.7’)
9.3 m W
et (30.6’)
Disp. Per Stroke
..................
1.1 L (.29 gal)
1
Max. Flow Rate
...............
413 lpm (109 gpm)
Max. Size Solids
.................
7.9 mm (5/16”)
1
Displacement per stroke was calculated at 4.8 bar (70 psig) air inlet pressure against a 2.1 bar (30 psig) head pressure.
The Efficiency Management System (EMS) can be used to optimize the performance of your Wilden pump for specific applications. The pump is delivered with the EMS adjusted to setting 4, which allows maximum flow
.
The
EMS
curve
allows
the
pump
user
to deter
-
mine flow and air consumption at each EMS setting. For any EMS setting and discharge pressure, the X factor is used as a multiplier with the original values from the setting 4 per
-
formance curve to calculate the actual flow and air consumption values for that specific EMS setting.
NOTE: Y
ou can
interpolate be
-
tween the setting curves for operation at in
-
termediate EMS settings.
EXAMPLE
A PX400 aluminum,full-stroke PTFE-fitted pump operating at EMS setting 4, achieved a flow rate of 265 lpm (70 gpm) using 136 Nm
3
/h
(80 scfm) of air when run at 6.2 bar (90 psig) air inlet pressure and 2.8 bar (40 psig) discharge pressure (see dot on performance curve). The end user did not require that much flow and wanted to reduce air consumption at his facility
. He determined that EMS setting 2
would meet his needs. At 2.8 bar (40 psig) discharge pressure and EMS
setting
2,
the
flow
X
factor
is
0.72
and
the
air
X
factor
is
0.52
(see dots on EMS curve). Multiplying the original setting 4 values by the X factors provides the setting 2 flow rate of 191 lpm (50 gpm) and an air consumption of 71 Nm
3
/h (42 scfm). The flow rate was reduced by 28% while
the air consumption was reduced by 48%, thus providing increased efficiency
.
For a detailed example for how to set your EMS, see beginning of performance curve section. Caution: Do not exceed 8.6 bar (125 psig) air supply pressure
.
p E r F o r m a n c E
PX400 Performance 23 WILDEN PUMP & ENGINEERING, LLC
The Efficiency Management System (EMS) can be used to optimize the performance of your Wilden pump for specific applications. The pump is delivered with the EMS adjusted to setting 4, which allows maximum flow
.
s
E
TT
iNg 4 PERFORMANCE CuR
vE
EMs CuR
vE
PX40
0
ALUMINUM – FULL S
TROKE PTFE-FITTED
TECHNIC
AL D
A
TA
Height
..........................
594 mm (23.4”)
Width
...........................
343 mm (13.5”)
Depth
...........................
310 mm (12.2”)
Ship W
eight
............
Aluminum 33 kg (72 lbs.)
Air Inlet
..........................
19 mm (3/4”)
Inlet
. . . . . . . . . . . . . . . . . . . . . . . . . . . .
38 mm (1-1/2”)
Outlet
...........................
38 mm (1-1/2”)
Suction Lift
.....................
5.7m Dry (18.7’)
9.3 m W
et (30.6’)
Disp. Per Stroke
..................
1.1 l (.29 gal.)
1
Max. Flow Rate
.............
413 lpm (109.1 gpm)
Max. Size Solids
.................
7.9 mm (5/16”)
1
Displacement per stroke was calculated at 4.8 bar (70 psig) air inlet pressure against a 2.1 bar (30 psig) head pressure.
The Efficiency Management System (EMS) can be used to optimize the performance of your Wilden pump for specific applications. The pump is delivered with the EMS adjusted to setting 4, which allows maximum flow
.
The EMS curve allows the pump user to
deter
-
mine flow and air consumption at each EMS setting. For any EMS setting and discharge pressure, the “X
factor” is used as
a multi
-
plier with the original values from the setting 4 performance curve to calculate the actual flow and air consumption values for that spe
-
cific EMS setting. Note: you can interpolate between the setting curves for operation at intermediate EMS settings.
EXAMPLE
A PX400 aluminum, Full Flow PTFE fitted pump operating at EMS setting 4, achieved a flow rate of 265 lpm (70 gpm) using 136 Nm
3
/h
(80 scfm) of air when run at 6.2 bar (90 psig) air inlet pressure and 2.8 bar (40 psig) discharge pressure (See dot on performance curve). The end user did not require that much flow and wanted to reduce air consumption at his facility
. He determined that EMS setting 2
would meet his needs. At 2.8 bar (40 psig) discharge pressure and EMS setting 2, the flow “X factor” is 0.72 and the air “X factor” is 0.52 (see dots on EMS curve). Multiplying the original setting 4 values by the “X factors” provides the setting 2 flow rate of 191 lpm (50 gpm) and an air consumption of 71 Nm
3
/h (42 scfm). The flow rate was reduced by 28% while
the air consumption was reduced by 48%, thus providing increased efficiency
.
For a detailed example for how to set your E
ms
, see beginning of
performance curve section. caution: Do not exceed 8.6 bar (125 psig) air supply pressure
.
P E R f o R M A n C E
PX400 Performance 23 WILDEn PUMP & EngInEERIng, LLC
The Efficiency Management System (EMS) can be used to optimize the performance of your Wilden pump for specific applications. The pump is delivered with the EMS adjusted to setting 4, which allows maximum flow
.
s
E
TT
iN
g
4 P
ER
FO
RM
ANC
E
C
uR
vE
EM
s C
uR
vE
PX40
0 A
LUM
IN
UM – FU
LL
S
T
R
OKE
P
T
FE
-F
ITTE
D
TEC
H
NIC
A
L DA
TA
Height
..........................
594 mm (23.4”)
Width
...........................
343 mm (13.5”)
Depth
...........................
310 mm (12.2”)
ship W
eight
............
Aluminum 33 kg (72 lbs.)
Air Inlet
..........................
19 mm (3/4”)
Inlet
. . . . . . . . . . . . . . . . . . . . . . . . . . . .
38 mm (1-1/2”)
Outlet
...........................
38 mm (1-1/2”)
suction Lift
.....................
5.7m Dry (18.7’)
9.3 m W
et (30.6’)
Disp. Per stroke
..................
1.1 l (.29 gal.)
1
max. Flow Rate
.............
413 lpm (109.1 gpm)
max. size solids
.................
7.9 mm (5/16”)
1
Displacement per stroke was calculated at 4.8 bar (70 psig) air inlet pressure against a 2.1 bar (30 psig) head pressure.
The Efficiency management system (E
ms
)
can be used to optimize the performance of your Wilden pump for specific applications. The pump is delivered with the E
ms
adjusted
to setting 4, which allows maximum flow
.
The E
ms
curve allows the pump
user to deter
-
mine flow and air consumption at each E
ms
setting. For any E
ms
setting and discharge
pressure, the “X
factor” is used
as a
multi
-
plier with the original values from the setting 4 performance curve to calculate the actual flow and air consumption values for that spe
-
cific E
ms
setting. Note: you can interpolate
between the setting curves for operation at intermediate Ems settings.
E
XAMP
LE
A PX400 aluminum, Full
stroke PTFE fitted pump operating at E
ms
setting 4, achieved a flow rate of 265 lpm (70 gpm) using 136 Nm
3
/h
(80 scfm) of air when run at 6.2 bar (90 psig) air inlet pressure and 2.8 bar (40 psig) discharge pressure (see dot on performance curve). The end user did not require that much flow and wanted to reduce air consumption at his facility
. He determined that E
ms
setting 2
would meet his needs. At 2.8 bar (40 psig) discharge pressure and Ems
setting 2, the flow “X factor” is 0.72 and the air “X factor” is
0.52 (see dots on Ems curve). m
ultiplying the original setting 4 values by the “X factors” provides
the setting 2 flow rate of 191 lpm (50 gpm) and an air consumption of 71 Nm
3
/h (42 scfm). The flow rate was reduced by 28% while
the air consumption was reduced by 48%, thus providing increased efficiency
.
for a detailed example for how to set your EM
s, see beginning of
performance curve section. Caution: do not exceed 8.6 bar (125 psig) air supply pressure
.