Dover PSG WILDEN SANIFLO PS2 Series, Инженерия, эксплуатация и обслуживание

Страница: 11 / 36

WIL-12330-E-08
Wilden ®
11
Suggested Installation, Operation, Maintenance and Troubleshooting
Wilden pumps are designed to meet the performance requirements of
even the most demanding pumping applications. They have been
designed and manufactured to the highest standards and are available in
a variety of liquid path materials to meet your chemical resistance needs.
Refer to the performance section of this manual for an in-depth analysis of
the performance characteristics of your pump. Wilden offers the widest
variety of elastomer options in the industry to satisfy temperature,
chemical compatibility, abrasion resistance and flex concerns.
The suction pipe size should be equivalent or larger than the diameter
of the suction inlet on your Wilden pump. The suction hose must be
non-collapsible, reinforced type as these pumps are capable of pulling a
high vacuum. Discharge piping should also be equivalent or larger than
the diameter of the pump discharge to minimize friction losses. It is
critical that all fittings and connections are airtight or a reduction or loss
of pump suction capability will result
.
CAUTION: All fittings and connections must be airtight.
Otherwise, pump suction capability will be reduced or lost.
Months of careful planning, study and selection efforts can result in
unsatisfactory pump performance if installation details are left to chance.
Premature failure and long-term dissatisfaction can be avoided if
reasonable care is exercised throughout the installation process
.
Location
Noise, safety and other logistical factors usually dictate where
equipment will be situated on the production floor. Multiple installations
with conflicting requirements can result in congestion of utility areas,
leaving few choices for additional pumps.
Within the framework of these and other existing conditions, every
pump should be located in such a way that the following key factors are
balanced against each other to maximum advantage:
• Access: First of all, the location should be accessible. If it’s easy to
reach the pump, maintenance personnel will have an easier time
carrying out routine inspections and adjustments. Should major
repairs become necessary, ease of access can play a key role in
speeding the repair process and reducing total downtime.
• Air Supply: Every pump location should have an air line large
enough to supply the volume of air necessary to achieve the
desired pumping rate. Do not exceed the maximum rated air
pressure.
For best results, the pumps should use a 5µ (micron) air filter, needle
valve and regulator. The use of an air filter before the pump will
ensure that the majority of any pipeline contaminants will be
eliminated.
• Solenoid Operation: When operation is controlled by a solenoid
valve in the air line, three-way valves should be used. This valve
allows trapped air between the valve and the pump to bleed off,
which improves pump performance. You can estimate pumping
volume by counting the number of strokes per minute, and then
multiplying that figure by the displacement per stroke.
• Muffler: Sound levels are reduced below OSHA specifications using
the standard Wilden muffler. Other mufflers can be used to further
reduce sound levels, but they usually reduce pump performance.
• Elevation: Selecting a site that is well within the pump’s dynamic
lift capability will assure that loss-of-prime issues will be eliminated.
In addition, pump efficiency can be adversely affected if proper
attention is not given to site location.
• Piping: Final determination of the pump site should not be made
until the piping challenges of each possible location have been
evaluated. The impact of current and future installations should be
considered ahead of time to make sure that inadvertent restrictions
are not created for any remaining sites.
The best choice possible will be a site involving the shortest and
straightest hook-up of suction and discharge piping. Unnecessary
elbows, bends and fittings should be avoided. Pipe sizes should be
selected to keep friction losses within practical limits. All piping
should be supported independently of the pump. In addition, the
piping should be aligned to avoid placing stress on the pump
fittings.
Flexible hose can be installed to aid in absorbing the forces created
by the natural reciprocating action of the pump. If the pump is to be
bolted down to a solid location, a mounting pad placed between the
pump and the foundation will assist in minimizing pump vibration.
Flexible connections between the pump and rigid piping will also
assist in minimizing pump vibration. If quick-closing valves are
installed at any point in the discharge system, or if pulsation within a
system becomes a problem, a surge suppressor (SD Equalizer®)
should be installed to protect the pump, piping and gauges from
surges and water hammer.
If the pump is to be used in a self-priming application, make sure
that all connections are airtight and that the suction lift is within the
model’s ability.
NOTE: Materials of construction and elastomer material
have an effect on suction-lift parameters. Please refer to the
performance section for specifics.
When pumps are installed in applications involving flooded suction or
suction head pressures, a gate valve should be installed in the
suction line to permit closing of the line for pump service.
Pumps in service with a positive suction head are most efficient
when inlet pressure is limited to 0.5–0.7 bar (7–10 psig). Premature
diaphragm failure may occur if positive suction is 0.7 bar (10 psig)
and higher.
Single-Point Exhaust
Pro-Flo SHIFT pumps can be used for submersible applications,
when using the Pro-Flo SHIFT single-point exhaust option.
CAUTION: All Wilden pumps are capable of passing solids.
a strainer should be used on the pump intake to ensure that
the pump´s rated solids capacity is not exceeded.
Section 6