manualshive.com logo in svg

Dover PSG WILDEN Pro-Flo SHIFT PS1, Инженерия, эксплуатация и обслуживание

Поделиться
Скачать
Dover PSG WILDEN Pro-Flo SHIFT PS1 Скачать руководство пользователя страница 8

 

WIL-10470-E-05  

8 

PS1 Clamped Metal 

 

SECTION 5 

 

PS1 METAL 
RUBBER-FITTED

 

 

Ship Weight…………….Aluminum 6 kg (13 lb) 

316 Stainless Steel 9 kg (20 lb) 

Alloy C 9.5 kg (21 lb) 

Air Inlet…………………………….13 mm (1/2") 

Inlet………………………………...13 mm (1/2") 

Outlet………………………………13 mm (1/2") 

Suction Lift……………………5.9 m Dry (19.3') 

9.8 m Wet (32.3') 

Disp. Per Stroke

1

……….…..0.10 L (0.027 gal) 

Max. Flow Rate…………..60.2 lpm (15.9 gpm) 

Max. Size Solids……………….1.6 mm (1/16") 

 

1

Displacement per stroke was calculated at 4.8 

bar (70 psig) air inlet pressure against a 2.1 bar 

(30 psig) head pressure. 

Example:

 To pump 20.1 lpm (5.3 gpm) 

against a discharge head of 3.4 bar  
(50 psig) requires 4.1 bar (60 psig) and  

7.7 Nm

3

/h (4.8 scfm) air consumption. 

Flow rates indicated on chart were determined by pumping water. For optimum life and performance, pumps 
should be specified so that daily operation parameters will fall in the center of the pump's performance curve. 
 

Caution: Do not exceed 8.6 bar (125 psig) air supply pressure.  

For UL-listed pumps, do not exceed 3.4 bar (50 psig) air supply pressure.

 

 

PS1 METAL 

TPE-FITTED

 

 

Ship Weight…………….Aluminum 6 kg (13 lb) 

316 Stainless Steel 9 kg (20 lb) 

Alloy C 9.5 kg (21 lb) 

Air Inlet…………………………….13 mm (1/2") 

Inlet………………………………...13 mm (1/2") 

Outlet………………………………13 mm (1/2") 

Suction Lift……………………5.7 m Dry (18.7') 

8.3 m Wet (27.2') 

Disp. Per Stroke

1

…………...0.10 L (0.026 gal) 

Max. Flow Rate…………..60.2 lpm (15.9 gpm) 

Max. Size Solids……………….1.6 mm (1/16") 

 

1

Displacement per stroke was calculated at 4.8 

bar (70 psig) air inlet pressure against a 2.1 bar 

(30 psig) head pressure. 

Example:

 To pump 20.8 lpm (5.5 gpm) 

against a discharge head of 3.4 bar  

(50 psig) requires 4.1 bar (60 psig) and  
8.3 Nm

3

/h (5.2 scfm) air consumption.

 

Flow rates indicated on chart were determined by pumping water. For optimum life and performance, pumps 
should be specified so that daily operation parameters will fall in the center of the pump's performance curve. 
 

Caution: Do not exceed 8.6 bar (125 psig) air supply pressure.  
For UL-listed pumps, do not exceed 3.4 bar (50 psig) air supply pressure.

 

 

 

PERFORMANCE 

Содержание PSG WILDEN Pro-Flo SHIFT PS1





























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды