Dover PSG WILDEN Pro-Flo SHIFT PS1 Скачать руководство пользователя страница 5

Страница: 5 / 28

WIL-10470-E-05

PS1 Clamped Metal

SECTION 2

MATERIAL CODES

MODEL

XPS1 = PRO-FLO

SHIFT ATEX

PS1 = PRO-FLO

SHIFT

WETTED PATH

A = ALUMINUM
H = ALLOY C
S = STAINLESS STEEL

OUTER PISTON

A = ALUMINUM
H = ALLOY C
S = STAINLESS STEEL
Z = NO OUTER PISTON

AIR CHAMBERS

A = ALUMINUM
N = NICKEL-PLATED
S = STAINLESS STEEL

CENTER BLOCK

AA = ALUMINUM

AIR VALVE

A = ALUMINUM

DIAPHRAGMS

BNS = BUNA-N (RED DOT)
EPS = EPDM (BLUE DOT)
FSS = SANIFLEX™

1,3

[HYTREL

(CREAM)]

TEU = PTFE W/EPDM BACK-UP

1,2,3

THU = PTFE W/HIGH TEMP

BUNA-N BACK-UP

TNL = PTFE W/NEOPRENE

BACK-UP O-RING, IPD

TNU = PTFE W/NEOPRENE

BACK-UP

TSU = PTFE W/SANIFLEX™

BACK-UP

1,2,3

TVU = PTFE W/FKM BACK-UP

VTS FKM (WHITE DOT)

WFS = WIL-FLEX™ [SANTOPRENE

(THREE BLACK DOTS)]

VALVE BALLS

BN = BUNA-N (RED DOT)
EP = EPDM (BLUE DOT)
FS = SANIFLEX™

[HYTREL

(CREAM)]

TF = PTFE

1,2,3

(WHITE)

VT = FKM (WHITE DOT)
WF = WIL-FLEX™ [SANTOPRENE

(THREE BLACK DOTS)]

VALVE SEATS

A = ALUMINUM
H = ALLOY C
S = STAINLESS STEEL

VALVE SEAT O-RINGS

BN = BUNA-N (RED DOT)
EP = EPDM (BLUE DOT)
FS = SANIFLEX™

1,3

[HYTREL

(CREAM)]

TF = PTFE

1,2,3

WF = WIL-FLEX™ [SANTOPRENE

(THREE BLACK DOTS)]

NOTES:

Meets Requirements of FDA CFR21.177

Meets Requirements of USP Class VI

Meets Requirements of 1935/2004/EC

SPECIALTY CODES

0014 BSP

0023 Wing nuts
0067 Saniflo™ FDA, Wil-Gard 220V
0070 Saniflo™ FDA

0079 Tri-clamp fittings, wing nuts

0080 Tri-clamp fittings ONLY
0100 Wil-Gard 110V
0102 Wil-Gard sensor wires ONLY
0103 Wil-Gard 220V

0319 Single-point exhaust, BSPT

0320 Single-point exhaust
0495 UL-approved
0502 PFA-coated hardware

0603 PFA-coated hardware, Wil-Gard 110V

0067E Saniflo™ FDA, Wil-Gard 220V 1935/2004/EC
0070E Saniflo™ FDA 1935/2004/EC
0120E Saniflo™ FDA, Wil-Gard 110V 1935/2004/EC

NOTE:

Most elastomeric materials use colored dots for identification

NOTE:

Not all models are available with all material options

NOTE:

The Wilden UL 79-listed products covered by this manual are PS1 models with the following designation: AA, followed by AA,

followed by A, followed by BNS, followed by BN, followed by A or S, followed by BN, followed by 0495. Wilden UL-Listed pumps
have been evaluated for use at a 25°C (77°F) ambient temperature with a maximum inlet pressure of 3.4 bar (50 psig).

PS1 METAL

LEGEND XPS 1 / X X X

X / X X X / X X / X X X / X X X X

13 mm (1/2") Pump

Maximum Flow Rate:
60.2 lpm (15.9 gpm)

O-RINGS

MODEL VALVE

SEATS SPECIALTY

VALVE

BALLS

CODE

DIAPHRAGMS

AIR VALVE

CENTER

BLOCK

OUTER

PISTON

WETTED

PATHS

WILDEN PUMP DESIGNATION SYSTEM

(if applicable)

Содержание PSG WILDEN Pro-Flo SHIFT PS1





























Результаты поиска

Содержание PSG WILDEN Pro-Flo SHIFT PS1

Отзывы:

Бренды по названию

Популярные бренды

Dover PSG WILDEN Pro-Flo SHIFT PS1, Инженерия, эксплуатация и обслуживание

Результаты поиска

Содержание PSG WILDEN Pro-Flo SHIFT PS1

Отзывы:

Бренды по названию

Популярные бренды