manualshive.com logo in svg

Dover PSG WILDEN HS430S, Руководство пользователя

Поделиться
Скачать
Dover PSG WILDEN HS430S Скачать руководство пользователя страница 8

 

WIL-11113-E-04  

8 

HS430S High Pressure Bolted Metal 

 

SECTION 5 

 

HS430S ALUMINUM 
TPE-FITTED

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

Ship Weight……………………….29 kg (64 lb) 

Air Inlet……………………..…….................3/4" 

Inlet…………………………….38 mm (1-1/2") 

Outlet……………………………38 mm (1-1/2") 

Suction Lift……………………..2.0 m Dry (6.8') 

9.0 m Wet (29.5')  

Disp. Per Stroke

1

…………….1.66 L (0.44 gal) 

Max. Flow Rate……………..280 lpm (74 gpm) 

Max. Size Solids…………………6.4 mm (1/4") 

 

1

Displacement per stroke was calculated at 4.8 

bar (70 psig) air inlet pressure against a 2.1 bar 

(30 psig) head pressure. 

Example:

 To pump 60 lpm (16 gpm) against 

a discharge head of 7.6 bar  
(110 psig) requires 6.9 bar (100 psig)  

and 84.9 Nm3/h (50 scfm) air consumption. 

Flow rates indicated on chart were determined by pumping water. For optimum life and performance, pumps 
should be specified so that daily operation parameters will fall in the center of the pump's performance curve. 
 

Caution: Do not exceed 8.6 bar (125 psig) air supply pressure.  

 

 
 

HS430S STAINLESS 

STEEL TPE-FITTED 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

Ship Weight……………………….29 kg (64 lb) 

Air Inlet……………………..…….................3/4" 

Inlet…………………………….38 mm (1-1/2") 

Outlet……………………………38 mm (1-1/2") 

Suction Lift……………………..2.0 m Dry (6.8') 

9.0 m Wet (29.5')  

Disp. Per Stroke

1

…………….1.55 L (0.41 gal) 

Max. Flow Rate……………..264 lpm (70 gpm) 

Max. Size Solids…………………6.4 mm (1/4") 

 

1

Displacement per stroke was calculated at 4.8 

bar (70 psig) air inlet pressure against a 2.1 bar 

(30 psig) head pressure. 

Example:

 To pump 49 lpm (13 gpm)  

against a discharge head of 4.8 bar  
(70 psig) requires 4.1 bar (60 psig)  

and 51 Nm3/h (30 scfm) air consumption. 

Flow rates indicated on chart were determined by pumping water. For optimum life and performance, pumps 
should be specified so that daily operation parameters will fall in the center of the pump's performance curve. 
 

Caution: Do not exceed 8.6 bar (125 psig) air supply pressure.  

 

 

 

PERFORMANCE 

PERFORMANCE 

Содержание PSG WILDEN HS430S

























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды