manualshive.com logo in svg

Dover PSG WILDEN HS430S, Руководство пользователя

Поделиться
Скачать
Dover PSG WILDEN HS430S Скачать руководство пользователя страница 15

 

WIL-11113-E-04  

15 

HS430S High Pressure Bolted Metal 

 

 

 

 

 

Step 10 

  Step 11 

  Step 12 

Inspect the diaphragm assembly for wear, 
damage or chemical attack. Replace any 
damaged components with genuine 
Wilden parts for reliable performance. 

  To remove the diaphragm assembly from 

shaft, secure shaft with soft jaws 
(aluminum, plastic, or plywood) to ensure 
the shaft is not damaged. Using an 
adjustable wrench, remove the diaphragm 
assembly from the shaft. 

  Remove outer piston and stud if 

equipped. Inspect for wear and replace if 
necessary. 

 

 

 

 

 

 

Step 13 

  Step 14 

Locate the outer piston on the side of the 
amplification chamber has an air 
passageway at the center of the outer 
piston lug. This air passageway allows air 
to flow from the opposite air chamber to the 
amplification chamber. This principle is how 
the HS430S high-pressure pump achieves 
a 2:1 ratio of inlet air pressure to discharge 
pressure. 

  When reassembling the HS430S pump, the outer piston (with the air passageway) has to 

be positioned on the same side as the amplification chamber. If it is not reassembled 
correctly, the pump will not operate, and process fluid will enter the air distribution system 
through the air passageway located at the shaft lug. 
 
This same air passageway continues through the diaphragm shaft, exits out of the 
diaphragm shaft via a 90º turn and into the air chamber located on the wetted side of the 
pump. The air passageway has to be positioned in the air chamber on the wetted side of 
the pump, opposite the amplification chamber. 
 

 

DISASSEMBLY / REASSEMBLY 

Содержание PSG WILDEN HS430S

























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды