manualshive.com logo in svg

Dover PSG BLACKMER MLN4B, Инструкции по установке, эксплуатации и обслуживанию, Страница: 15 / 20

Поделиться
Скачать
Dover PSG BLACKMER MLN4B Скачать руководство пользователя страница 15

106-A00    Page 15/20 

MAINTENANCE: MLN4B, MRLN4B

 

 

7.  Follow Steps 2 through 5 to install the remaining head 

and hub assemblies. Remember to grease the casing 
chamfer and the three head chamfers. 

8.  PACKING AND PACKING FOLLOWER 

When necessary to repack, use a full set of new 
packing rings (19). Packing is furnished in sets with the 
correct number of rings. Never add new rings to an old 
set of packing. 
a.  Insert the packing washer (58) into the stuffing box 

of the inboard hub (20C). 

b.  Insert each packing ring (19) separately into the 

stuffing box, using the packing follower (75) to 
properly seat each ring after placement. Be sure to 
stagger the split joints approximately 180 degrees 
apart so that they are not overlapping or near the 
joint of the preceding ring. 

c.  After the packing rings are in place, install and 

tighten the two packing follower removal nuts (18A) 
against the hub (20C).  

d.  Place the packing follower (75) snugly against the 

packing (19). Install the two packing follower stud 
nuts (18) and tighten lightly. 

 

 

Failure to stop the pump before 
adjusting the shaft packing can cause 
severe personal injury. 

Hazardous 

machinery can 

cause serious 

personal injury. 

9. 

PACKING ADJUSTMENT – 

Packing must be properly 

adjusted to prevent overheating. 
a.  While the liquid is being pumped, check for leakage 

from the stuffing box.  STOP the pump and uniformly 
tighten the packing follower stud nuts (18) 1/4 turn at 
a time to reduce leakage. 

b.  Restart the pump and check the stuffing box 

temperature several minutes after each adjustment 
for signs of overheating. 

c.  Check the packing (19) again after 20-30 minutes of 

running the pump, and readjust if necessary. 

NOTE: 

Some leakage is desirable to lubricate the 

packing, but in some cases is unacceptable, depending 
on the application. 

10. BLACKMER TRIPLE-LIP SEAL (if equipped) 

On pumps equipped with a Blackmer triple-lip seal, refer 
to the separate literature accompanying the triple-lip 
seal for installation instructions. 

11. COMMERCIAL MECHANICAL SEAL (if equipped 

On pumps equipped with a commercial mechanical 
seal, refer to the separate literature accompanying the 
mechanical seal for installation instructions. 

12. RELIEF VALVE ASSEMBLY (if equipped) 

a.  Insert the valve (9) into the relief valve body (6) with the 

fluted end inward. 

b.  Install the relief valve spring (8), spring guide (7) and 

guide rod (45) against the valve. 

c.  Attach a new relief valve gasket (10) and the valve 

cover (4) on the cylinder. 

d.  Screw the relief valve adjusting screw (2) into the valve 

cover until it makes contact with the spring guide (7). 

e.  Install the relief valve cap (1) and gasket (88) after the 

relief valve has been precisely adjusted. 

NOTICE: 

The relief valve setting MUST be tested and adjusted 
more precisely before putting the pump into service.  
Refer to "Relief Valve Setting and Adjustment" 

13. 

Reinstall coupling, shaft key (35), and coupling guards.

 

14. SHAFT COVER 

a.  Install the shaft cover O-ring (26) in the groove in the 

shaft cover. 

b.  Lubricate the chamfer on the outboard hub, and slide 

the shaft cover (27) over the shaft against the hub. 

c.  Install and tighten the two shaft cover capscrews (28). 

Operation without guards in place can 
cause serious personal injury, major 
property damage, or death. 

Do not operate 

without guard in 

place. 

15. 

Refer to “Pre-Start Up Check List” and “Start Up 
Procedures” sections of this manual prior to pump 
operation.

 

Содержание PSG BLACKMER MLN4B





















Отзывы:

Нет отзывов