Dover Hydro systems AquaBlend 0.2%-2% WSP Скачать руководство пользователя страница 14

Страница: 14 / 14

Congratulations on Your Purchase

We make the best and most reliable fluid-driven injectors

available. Hydro Systems will provide for replacement of all

parts proven to be defective in material or workmanship

from the date of purchase for the following periods:

year

Covers your unit from

manufacturing and material

defects only.

Hydro Systems products are warranted to be free from

defects in materials and workmanship for the above time

frames. Hydro Systems will at its sole option repair or

replace any component that fails in normal use. Any repairs

made under warranty shall not extend the initial warranty

period.

To Maintain Your Warranty

Your only responsibility is ordinary maintenance - filtering

incoming fluid, replacing the O-ring and dosage piston/

gasket when worn. Seals and O-rings are not covered under

the warranty

To Return an injector for Warranty or Non-Warranty repair:

Contact Hydro Systems Company or your local distributor for return information.

Warranty

This warranty is not valid if the defects are found to be due to

the product’s misuse, lack of maintenance, fluid impurities

such as sand or iron, defective installation, freezing, fluid

hammer, abuse, unwanted side effects due to the chemicals

you choose to inject or service provided by anyone who is not

an authorized service provider. Hydro Systems declines any

responsibility if the product is not used

in compliance with the

operating instructions and specifications as indicated in this

owner’s manual.

IN NO EVENT SHALL HYDRO SYSTEMS BE LIABLE FOR ANY

INCIDENTAL, SPECIAL; INDIRECT, OR CONSEQUENTIAL DAMAGES,

WHETHER RESULTING FROM THE USE, MISUSE OR INABILITY TO

USE THIS PRODUCT OR FROM DEFECTS IN THE PRODUCT.

There is no warranty expressed or implied relating in any way

to products used in conjunction with Hydro Systems.

Hydro Systems or authorized distributor shall not be liable for

incidental or consequential damage, such as any economic loss.

Hydro Systems retains the exclusive right to repair or replace the

product. Such remedy shall be your sole and exclusive remedy

for any breach of warranty. There are no warranties, expressed

or implied, which extend beyond those described above.

Содержание Hydro systems AquaBlend 0.2%-2% WSP















Результаты поиска

Содержание Hydro systems AquaBlend 0.2%-2% WSP

Отзывы:

Бренды по названию

Популярные бренды

Dover Hydro systems AquaBlend 0.2%-2% WSP, Руководство по эксплуатации

Результаты поиска

Содержание Hydro systems AquaBlend 0.2%-2% WSP

Отзывы:

Бренды по названию

Популярные бренды