background image

15

6.O1 Limited Warranty

 

Seller

 warrants solely to 

Buyer

 the Products will be free from defects in material and workmanship under normal use and 

service for a period of one year from the date of completion of manufacture. This limited warranty does not apply to (a) hoses; 
(b) and products that have a normal life shorter than one year; or (c) failure in performance or damage caused by chemicals, 
abrasive materials, corrosion, lightning, improper voltage supply, physical abuse, mishandling or misapplication. In the event 
the Products are altered or repaired by 

Buyer

 without 

Seller’s

 prior written approval, all warranties will be void.

No other warranty, oral, express or implied, including any warranty of merchantability or fitness for any particular 
purpose, is made for these products, and all other warranties are hereby expressly excluded.

Seller’s

 sole obligation under this warranty will be, at 

Seller’s

 option, to repair or replace F.O.B.

 Seller’s

 facility in Cincinnati, 

Ohio any Products found to be other than as warranted.

6.O2 Limitation of Liability

Seller’s

 warranty obligations and 

Buyer’s

 remedies are solely and exclusively as stated herein. 

Seller 

shall have no other 

liability, direct or indirect, of any kind, including liability for special, incidental, or consequential damages or for any other claims 
for damage or loss resulting from any cause whatsoever, whether based on negligence, strict liability, breach of contract or 
breach of warranty.

6.OO warranty 

Hydro Systems

3798 Round Bottom Road
Cincinnati, OH 45244

Phone  

513.271.88OO

Toll Free

 

 

8OO.543.7184 

Fax

  

513.271.O16O

Web

  

hydrosystemsco.com

HYD10099002  Rev A 9/18

Congratulations on Your Purchase!

We make the best and most reliable fluid-driven injectors available. 
Hydro Systems will provide for replacement of all parts proven to 
be defective in material or workmanship from the date of purchase 

for the following periods:  

1

 Year

Covers your unit from manufacturing 
and material 
defects only.

Hydro Systems products are warranted to be free from defects 
in materials and workmanship for the above time frames. Hydro 
Systems will at its sole option repair or replace any component 
that fails in normal use. Any repairs made under warranty shall not 
extend the initial warranty period.

To Maintain Your Warranty

Your only responsibility is ordinary maintenance - filtering incoming 
fluid, replacing the O-ring and dosage piston/gasket when worn. 
Seals and O-rings are not covered under the warranty. 

To Return an injector for Warranty or Non-Warranty repair:

Contact Hydro Systems Company or your local distributor for return information.

This warranty is not valid if the defects are found to be due to the 
product’s misuse, lack of maintenance, fluid impurities such as 
sand or iron, defective installation, freezing,  fluid hammer, abuse, 
unwanted side effects due to the chemicals you choose to inject 
or service provided by anyone who is not an authorized service 
provider. Hydro Systems declines any responsibility if the product 
is not used in compliance with the operating instructions and 
specifications as indicated in this owner’s manual. 

IN NO EVENT SHALL HYDRO SYSTEMS BE LIABLE FOR ANY 
INCIDENTAL, SPECIAL; INDIRECT, OR CONSEQUENTIAL DAMAGES, 
WHETHER RESULTING FROM THE USE, MISUSE OR INABILITY TO 
USE THIS PRODUCT OR FROM DEFECTS IN THE PRODUCT.

There is no warranty expressed or implied relating in any way to 
products used in conjunction with Hydro Systems.

Hydro Systems or authorized distributor shall not be liable for 
incidental or consequential damage, such as any economic loss. 
Hydro Systems retains the exclusive right to repair or replace the 
product. Such remedy shall be your sole and exclusive remedy for any 
breach of warranty. There are no warranties, expressed or implied, 
which extend beyond those described above.

6.O2 Contact

Содержание HYDRO AquaBlend Xtreme
















Отзывы: