Dover HEIL LIBERTY TP1L-SM-0520 Скачать руководство пользователя страница 91 | Manualshive

Страница: 91 / 136

background image

Issued May 2020

Maintenance and Adjustment

Copyright 2020, Heil Environmental
Printed in the U.S.A.

Maintenance and Adjustment

85

DRAIN AND CLEAN THE HYDRAULIC OIL TANK (CONTINUED)

NOTICE

Before filling the tank be sure the funnel is clean and 200 mesh (or finer) screen is used to strain the hydraulic oil.

13.Fill tank with recommended oil, checking the sight gauge as you fill. Refer to

Hydraulic Oil Specifications

.

14.Check the entire system to make sure all connections are tight and no leaks are found.

15.Start the truck’s engine and engage the pump.

WARNING

Moving equipment can be dangerous to bystanders. Serious injury or death can occur if a person is in the wrong area or is
not attentive to the operations. Clear the area of all unnecessary people before you operate the controls.

16.Operate the packing panel through 10 cycles to be sure all air is out of the circuits.

17.Operate the automated container lift mechanism.

18.Operate tailgate – full up and full down.

19.Operate body raise (dump units) – full up and full down.

20.With the packing panel in the retracted position and lift in the in-transit position, check tank oil level. If necessary, add

recommended as described under

Check Oil Level

.

PURGE THE HYDRAULIC SYSTEM

If the hydraulic system becomes contaminated because of component failure or some other reason, you must purge the
hydraulic system.

To purge the system, follow these steps:

1. Extend the packer/ejector cylinder to lower the oil level in the tank.

2. Remove and replace the in-tank oil filter element in the tank.

3. Engage the packer/ejector control lever and allow the oil to circulate through the new filter, cleaning the oil.

NOTICE

Before filling the tank be sure the funnel is clean and 200 mesh (or finer) screen is used to strain the hydraulic oil.

4. Repeat the procedure as necessary until the system is purged.

NOTICE

If contaminated hydraulic oil reaches the cylinders, the unit may need to be removed from service until the contamination
is removed. For more information, contact the Heil Technical Services.

16

83

«
...
89
90
91
92
93
...
»

Содержание HEIL LIBERTY TP1L-SM-0520









































































































































Отзывы:

Нет отзывов

Похожие инструкции для HEIL LIBERTY TP1L-SM-0520

Бренд: Hagie Страницы: 61

Бренд: JackJaw Страницы: 2

Бренд: ICELED Страницы: 4

Бренд: Facom Страницы: 4

Бренд: FaceLake Страницы: 2

Бренд: FabiaTech Страницы: 2

Бренд: FabiaTech Страницы: 77

Бренд: York Страницы: 26

Бренд: hager Страницы: 4

Бренд: Goobay Страницы: 6

mocon AQUATRAN 3/38

Бренд: Ametek Страницы: 85

Бренд: Yacht Devices Страницы: 32

Бренд: RAB Страницы: 4

Бренд: ATD Tools Страницы: 7

SPLICE-500 MKII

Бренд: Serpent Страницы: 8

Бренд: Wecan Technology and Lighting Co., Ltd Страницы: 4

Бренд: Varan Motors Страницы: 70

Бренд: Nolangroup Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды