Dover HEIL LIBERTY TP1L-SM-0520 Скачать руководство пользователя страница 89 | Manualshive

Страница: 89 / 136

background image

Issued May 2020

Maintenance and Adjustment

Copyright 2020, Heil Environmental
Printed in the U.S.A.

Maintenance and Adjustment

83

CHECK OIL LEVEL

Check the hydraulic oil level (after warning up the oil) daily or every eight (8) hours, whichever comes first. Fill as
necessary.

Important: Contamination is a hydraulic system’s worst enemy. Do not let dirt enter the system. Use a clean rag and
remove dirt or other contamination around any system component before you disconnect or remove it. While you fill the
reservoir, filter the oil through a 200 mesh (or finer) screen. Never use a cloth to filter the oil.

WHEN TO CHANGE OIL FILTER ELEMENT

Change the filter more often under certain conditions such as an extremely dusty atmosphere or area. Use only Heil
replacement filters. Purchase the filter element from your local Heil distributor.

Change the filter element when oil analysis shows the oil has expired.

CHANGE HYDRAULIC OIL FILTER ELEMENT

Watch the Service Shack Video online at

www.Heil.com/Heil-Service-Shack

and selecting

Changing Filters

Replace the hydraulic filter element after first 30 days of operation, then every 6 months or 1000 hours of operation OR
when filter bypass light is ON. To change the hydraulic oil filter, refer to the figure below and follow these steps:

1. Using a 1/2" wrench, remove the four (4) nuts from the filter cover located on the hydraulic oil tank.

2. Set the nuts aside for reuse and then remove the filter cover.

3. Remove the filter element with the by-pass assembly and responsibly discard as required.

4. Clean the housing with a clean, lint-free cloth.

5. Check the o-ring and gasket. Replace them if necessary.

6. Lubricate all o-rings and gaskets.

7. Install new element.

8. Reinstall cover with nuts. Torque nuts to 13 ft-lbs.

Figure 32. Hydraulic Oil Filter

«
...
87
88
89
90
91
...
»

Содержание HEIL LIBERTY TP1L-SM-0520









































































































































Отзывы:

Нет отзывов

Похожие инструкции для HEIL LIBERTY TP1L-SM-0520

Бренд: Baker Hughes Страницы: 168

Бренд: Ace Страницы: 17

Бренд: ACE INSTRUMENTS Страницы: 33

Бренд: ACE INSTRUMENTS Страницы: 2

Бренд: ACE INSTRUMENTS Страницы: 2

Бренд: TapFlo Страницы: 35

Бренд: DANA Страницы: 8

Бренд: 2E Страницы: 6

Бренд: GALBIATI Страницы: 20

Бренд: Bard Страницы: 144

Бренд: GALBIATI Страницы: 8

Бренд: Vahva Jussi Страницы: 9

Бренд: CAB Страницы: 13

Бренд: CAB Страницы: 30

Бренд: CAB Страницы: 17

Бренд: CAB Страницы: 33

Camping Equipment

Бренд: C. Crane Страницы: 8

Бренд: C-Pro Direct Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды