Douwe EgbertsEgberts CAFITESSE 300 Скачать руководство пользователя страница 97

Страница: 97 / 100

The plugs of racing karts are susceptible to carbon
fouling, but how does Iridium Power do in this case?

We frequently hear that Iridium Power is resistant to carbon fouling compared to

plugs from other companies. However, there is no way that they are a 100%

solution, and it's good to know these techniques to prevent carbon fouling.

[1] When rolling in the race, close the carburetor's low

needle or pinch the fuel pipe with your hand to prevent

excess fuel from entering the engine.

[2] By pumping the accelerator during rolling, a rich fuel air

mixture goes into the engine, making it easier for

carbon fouling to occur. Operate the accelerator gently.

[3] If carbon fouling happens while running with the throttle fully open,

this could mean that the heat range is too low or that the fuel mix

is to rich. Consult with a kart shop to find the optimum setting.

How is the compatibility with plug cords such as Nology?

There are no particular issues with compatibility. In fact, there are some

cord manufactures who sell products "especially for iridium plugs."

When changing plugs, is there any need to
change the settings?

For normal vehicles, there is no need to change the settings.

It is advisable to reset vehicles with modified exhaust

systems, though in most cases adjusting the air screw is

sufficient. (Except for racing carburetors such as FCRs)

Is there a way to tell them apart when replacing them?

This can be done by confirming the level of wear (the gap width) on the ground electrode.

DENSO's Iridium electrodes are different from conventional products in that their center electrodes

hardly wear, and because of this it is better to check for wear on the ground electrode .

T h e t e r m i n a l o n t h e e n d o f t h e p l u g i s
frequently unnecessary on motorcycle, so
why is this included with all types?

Iridium Power comes standard with a plug terminal (not including

combined types). This is because some of the other companies'

plug cords require a terminal, and at DENSO we decide our

product specifications keeping in mind every customer.

Are  plugs  such  as  VUH27D  and  VK24PRZ11  for  Honda
vehicles  available  as  Iridium  Tough  plugs?    Will  they  last
100,000km?  Also, can Iridium Power be substituted here?

Plugs for 2-wheel vehicles with a "V" in the part number have a platinum tip

welded to the ground electrode, the same as in 4-wheel vehicles. They have

more durability than Iridium Power, but do last 100,000km. Thus we do not

offer them as Iridium Tough products. You can choose the Iridium Power

plug for those vehicle types with a compatible Iridium Power plug shown in

the Model Chart; however, please understand that it will be not as durable.

I'm using Iridium Power. If there is carbon
fouling, can I use a brass brush to clean the
plugs?

Because Iridium Power's center electrode has a fine 0.4mm diameter,

there is a chance that this electrode could be bent by a brass brush. If

you having the plug cleaned, a sandblaster-type plug cleaner found in

maintenance shops is preferable. If this is the case, keep the air

pressure low and clean the plug for as short a time period as possible.

Also, one trick would be to dissolve the carbon with an engine

conditioner or a similar chemical agent. (Parts cleaners will not

dissolve carbon). After applying it, take a nylon brush (don't use a

wire brush) and scrub it off, wash it well, and dry it off. Repeat this

procedure three or four times to remove any carbon. DENSO has

confirmed that this does not return the performance of the plugs to

100%, so please use this as a stopgap measure.

The vehicle seems to be running worse now that I've installed them?

In most cases there is a problem with the vehicle. Scooters are

often run for long periods of time without maintenance, and it is

common to see them with richer fuel-air mixtures from dirty air

cleaners. Our investigations have found that these vehicles tend

to be susceptible to carbon fouling, and when replacing plugs

also remember to inspect and clean the air cleaner. The

effectiveness of the change should become even more apparent.

Also for rough idling and problems starting, sometimes reducing

the plug gap by 0.1 to 0.2mm will solve the problem.

Содержание CAFITESSE 300





































































































Результаты поиска

Содержание CAFITESSE 300

Отзывы:

Похожие инструкции для CAFITESSE 300

Бренды по названию

Популярные бренды

Douwe EgbertsEgberts CAFITESSE 300, Руководство по обслуживанию

Результаты поиска

Содержание CAFITESSE 300

Отзывы:

Похожие инструкции для CAFITESSE 300

Бренды по названию

Популярные бренды