Douwe EgbertsEgberts CAFITESSE 300 Скачать руководство пользователя страница 94

Страница: 94 / 100

Will output and torque increase if I use Iridium
Power plugs?

These are chassis dynamo test results comparing a Vitz 1300 using Iridium

Power plugs and another which uses regular plugs are shown below.

With the normal plugs, the output is 98.2PS, while torque is 14.8 kgf; when

this was changed to the Iridium Power plugs, the output was 99.3PS, while

torque was 15.2 kgf. (This is approximately a 1.5% improvement in output.)

Will my exhaust emissions be cleaner if I put
on Iridium Power plugs?

Improved combustion efficiency will clean your exhaust emission! Fuel consumption will improve too!

With the superior ignitability of ultra-thin electrodes

(0.4mm), combustion efficiency will be improved.

◎Cleaner Exhaust Emissions

CO and CO2 levels will decrease in the "EURO III"

emissions test to be implemented in the future.

◎Improved Mileage

A great bonus for long-distance drivers.

Even for those who are concerned about the

environment, we recommend Iridium Power.

■

Iridium Plug Motorcycle Emissions Comparison Test

Test Vehicle

：CBR250

Test Conditions：EURO

Test Equipment：MEXA-7400, CVS 7100

Tested Plugs

：U24FER9 (Ni Plug) Gap: 0.85

：IUH24 (Ir Plug) Gap: 0.85

I have a 4AG engine NA tuned, with a Solex 44
dia. carburetor installed, giving a 200PS output.
Which plug is good for a car such as this?

DENSO has Iridium Power and Iridium Racing to meet the

needs of tuned and racing engines. For the engine

described in the question, the right plug should be around

Iridium Power IK (IQ) 22, 24, or 27. Here is an introduction

to using the different types of the Iridium Series on racing

engines.

●

Iridium Power:

NA Tuned (Short distance racing), Turbo tuned

where a regular turbine has been tuned to increase the boost.

●

Iridium Racing (01 Type):

The 01 Type is usually called

the slant ground electrode type. If your car is turbo tuned

where the turbine has been replaced and the boost pressure is

above 1.2 to 1.3kg/cm2, an Iridium Racing 01 type is needed.

Also, if a NA tuned engine with comparatively high vibration (4

cylinders) is to be raced over long distances, switching to this

type can increase the reliability of the ground electrodes.

●

Iridium Racing (02 Type):

The 02 type (flat ground

type) is appropriate for higher output engines than the 01

type, but because the spark position is withdrawn compared

to the 01 type, only consider this plug for racing applications.

Is there a standard for differentiating the
uses of Iridium Power and Iridium Racing?

Iridium Racing uses a platinum tip for the ground electrode and

a high strength fine insulator for racing. Also, there is a silicone

coating on the insulator giving it an increased resistance to

carbon fouling. However, because of the withdrawn spark

position, the Iridium Power has the high ignitability of the two.

Instead, because of the "extension" in engine revolution felt by

many at high revolutions, it is popular with customers who race.

Choose "Iridium Power" for response and "Iridium Racing" for

high revolutions. Iridium Racing is particularly popular on the

circuit scene. (In the '03 Motegi 7 Hour Open, it was found that

45% of the vehicles used Iridium Racing※) ※DENSO findings

120

100

135

180

km/h

(kgm)

Horsepower (Ir)
Power (Regular)
Horsepower (Ir)
Power (Regular)

Internal data

Test 1

24.5

24.6

24.7

24.8

CO（g/km）

EURO III Test Pattern

24.9

25.1

25.2

25.0523

24.7491

Test 2

25.1569

24.7826

U24FER9

IUH24

Regular Plug

Iridium Power

140

120

100

Speed

(km/h)

Time

Internal Data

Test 1

18.9

19.1

19.2

Fuel Consumption (km/L)

19.3

19.4

19.5

19.0967

19.4606

Test 2

19.1110

19.4241

Test 1

69.5

70.5

（g/km）

71.5

72.5

72.7682

70.9184

Test 2

72.1660

70.9778

Internal Data

Содержание CAFITESSE 300





































































































Результаты поиска

Содержание CAFITESSE 300

Отзывы:

Похожие инструкции для CAFITESSE 300

Бренды по названию

Популярные бренды

Douwe EgbertsEgberts CAFITESSE 300, Руководство по обслуживанию

Результаты поиска

Содержание CAFITESSE 300

Отзывы:

Похожие инструкции для CAFITESSE 300

Бренды по названию

Популярные бренды