Douwe EgbertsEgberts CAFITESSE 300 Скачать руководство пользователя страница 95

Страница: 95 / 100

Double

electrode plug

Needle and sphere

Plate and plate

Plate and needle

Regular Plug

Plug

Spark voltage

Low

High

Electrode

model

Ground

Center

Double electrode plug

Small cooling effect

Large cooling effect

I drive a GT-R tuned to 850HP. Would it be
okay to install 0.4mm dia. Iridium Power
series plugs?

The DENSO Iridium Series have the world's thinnest 0.4mm iridium

center electrodes, but because the durability of the iridium alloy

developed by DENSO is higher that even platinum, which has in the

past been said to be the most durable, it can be said that it's the best

plug for tuned engines. Specifically, it has the following advantages:

[1] Iridium alloy has a melting point and hardness above that of platinum, even

turbo, with its high combustion temperature, can be used with confidence.

Also, even when used with powerful ignition systems such as MSD and

MDI, these plugs are even more reliable than platinum racing plugs.

[2] The issue for high boost engines is that misfiring that occurs at high

revolutions. The fine electrodes of the Iridium series require a lower

voltage, allowing the energy generated by the coil to be sparked

without losses. It can be said the 0.4mm dia. DENSO Iridium

Power series are a strong ally of tuned high-boost turbo systems.

What is the optimum heat range for a tuned
up Golf4 GTI 1.8L Turbo?

(Tuning: Turbine Changed, High Volume Injector Installed,

and ROM Adjusted to give an output of 200PS from 150PS.)

It's difficult to give a heat range based on going from 150PS to 200PS

alone, and it's best if you judge the condition of your current plugs and

judge for yourself, but as a general rule, for boost pressures between

1.0 and 1.2kg/cm2, an IK24 should be sufficient. During the winter, #22

should improve starting and low speed feel. The heat range is different

depending on how the engine has been tuned and how it's used; using

an increase in heat range of 1 or 2 as a starting point, decide on a heat

range, always looking at the condition of your current plugs.

I  have  Rover  Mini  AT  ('90).    Since  changing  to
Iridium Power, the idling rotation in neutral went
up  400rpm  from  the  previous  plugs  (1000rpm
before the change, 1400rpm since).  Before the
c h a n g e ,   g o i n g   f r o m   n e u t r a l   t o   d r i v e   w a s
550rpm,  but  now  it  goes  below  550rpm  and
stalls.    The  revolutions  increase  smoothly  and
acceleration is good during driving.  Why is this?

Frequently for older vehicles, the ignition system has

degraded, and it is sometimes not possible to see the full

effect of Iridium Power. In this case, the spark gap should

be adjusted from 1.1mm to 0.8mm. Also, in the VK series,

there is the VK20Y plug where the gap has been preset to

0.8mm.

Can I replace my double, triple, or quadruple
electrode plugs to Iridium Power or Iridium Tough?

This is possible. The reason: because of the 0.4mm center electrode

in Iridium Power and Iridium Tough plugs, they have a lower spark

voltage compared to double, triple, and quadruple electrode plugs.

Please refer to the Standard Resistor Model Quick Chart.

■

Spark Voltage

The thinner the electrode is, the stronger the electrical field is. Because

the electrical field affects spark voltage, a thinner electrode lowers spark

voltage. If each type of electrode shape is modeled as shown below,

Iridium Tough has a lower voltage than double electrode plugs.

■

Ignitability

The more the contact area between the flame kernel and the electrode is

minimized, the smaller the cooling action from the electrodes and the better

ignitability is. Because of the 0.4mm center electrode, the contact area between

the flame kernel and the electrode is small, resulting in excellent ignitability.

Can an Iridium Power be installed on
an RX-7(SA22C Turbo Model)?

In the rotary engines in some old Mazda's on the T

(Trailing) side there is a plug, the terminal nut for which

must be removed. In others, the removal of the T side plug

terminal nut is necessary as in the Cosmo (HB22S).

DENSO has Iridium Racing plugs for rotary engines, with a

variety of heat ranges from #27 to #35. Iridium Racing

Plugs for Rotary Engines come standard with terminal

nuts.

How is the compatibility with trial vehicles.

The "IW series" is well suited for most trial vehicles. Though these

vehicles frequently use a low heat range, the heat ranges available for

Iridium Power starts with IW16, so choose one that matches the type of

driving you do. Better accelerator response and torque can be expected

with Iridium Power, which has excellent ignitability. Recently, the space

to install plugs in trial vehicles has shrunk, and there is a demand for

miniature plugs. In these cases try the IK types. However, the space

between the plug cord and the insulator will require waterproofing.

Содержание CAFITESSE 300





































































































Результаты поиска

Содержание CAFITESSE 300

Отзывы:

Похожие инструкции для CAFITESSE 300

Бренды по названию

Популярные бренды

Douwe EgbertsEgberts CAFITESSE 300, Руководство по обслуживанию

Результаты поиска

Содержание CAFITESSE 300

Отзывы:

Похожие инструкции для CAFITESSE 300

Бренды по названию

Популярные бренды