manualshive.com logo in svg

Dormakaba EML 310, Руководство по установке

Поделиться
Скачать
Dormakaba EML 310 Скачать руководство пользователя страница 15

dormakaba Header Installation Instructions with EML310/320 and 371/372
For use with DRS Rails and Patching Fittings (4-1/8”, 4-1/2”, 6” Headers) 

933903

07-2019

EML Header Shim

15

Install armature plate: DRS Rails

4.2 

(For use with DRS rails only)

Fig. 12 

 

4.2.1  Align armature plate via the 2 pins.

4.2.2  Secure armature plate to DRS rail with the 

following included center-mounting bolt 
fasteners:

• 

Bolt with affixed rubber washer

• 

Steel washer

• 

Rubber washer

• 

Steel washer

Center-

mounting 

bolt

Armat

ure 

plat

e

NOTE: Apply thread 

locking compound to 

exposed thread.

4.2.4  Close door and 

adjust 
armature 
plate if 
necessary.

NOTE:  Armature plate 
should remain movable. See 
step 4.2.3 on this page.

NOTE:  Armature plate 
must be allowed to pivot on 
the center-mounting bolt to 
allow proper alignment with 
the magnet surface. If not 
properly aligned with the 
magnet surface, the lock 
may lose holding force or 
not lock at all.

NOTE:  The head of the 
armature mounting bolt 
ships with a rubber washer 
affixed to it. Ensure this 
washer projects slightly 
beyond the surface of to 
armature plate. This is to 
allow the washer to expand 
when power is removed and 
break the air vacuum 
between the plate and the 
magnet surface. DO NOT 
REMOVE OR TRIM THE 
WASHER. This will cause the 
lock to continually have 
some holding force even 
when power is removed.

4.2.3 

NOTE: TIGHTEN 
CENTER-
MOUNTING 
BOLT BUT, 
ALLOW FOR 
ARMATURE 
PLATE 
MOVEMENT AND 
ALIGNMENT.

Pins

Armature 

plate

Mag lo

ck

DRS rail

Armature 

plate

Содержание EML 310






















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды