Dormakaba EML 310 Скачать руководство пользователя

Страница: 11 / 21

dormakaba Header Installation Instructions with EML310/320 and 371/372
For use with DRS Rails and Patching Fittings (4-1/8”, 4-1/2”, 6” Headers)

933903

07-2019

EML Header Shim

Disassembly mag lock

Secure header shim

3.1

Prepare/disassemble mag lock body and mounting bracket

3.2.1

Secure header shim to frame above or ceiling
surface using appropriate fasteners.

NOTE: May need to drill through header tube
depending on shim hole locations.

3.2

Secure header shim to frame/ceiling surface

(for 4-1/8” or 4-1/2” headers only)

Fig. 8

3.1.1

Remove anti-tamper screws to access
captive mounting screws.

3.1.3

Slide and lift mounting bracket from mag
lock body screws.

Anti-tamper

screws

Access to captive

mounting screws

Captive

mounting

screws

Mounting

bracket

Mag lock

body screws

Mounting

bracket

EML 371/372

header shim

shown.

Header

tube

NOTE: DO NOT REMOVE OR LOOSEN MAG

LOCK BODY SCREWS.

Hex key size

4mm

Same

instructions to

be used for

EML 310/320.

EML and shim installation instructions

Fig. 7

3.1.2

Unthread captive mounting screws from
bottom.

Header

shim

Содержание EML 310






















Результаты поиска

Содержание EML 310

Отзывы:

Похожие инструкции для EML 310

Бренды по названию

Популярные бренды

Dormakaba EML 310, Руководство по установке

Результаты поиска

Содержание EML 310

Отзывы:

Похожие инструкции для EML 310

Бренды по названию

Популярные бренды