Dormakaba EML 310 Скачать руководство пользователя страница 13

Страница: 13 / 21

dormakaba Header Installation Instructions with EML310/320 and 371/372
For use with DRS Rails and Patching Fittings (4-1/8”, 4-1/2”, 6” Headers)

933903

07-2019

EML Header Shim

Secure mounting bracket

3.4

Secure mounting bracket and mag lock to shim

(for 6” headers only)

Fig. 10

3.4.1

Secure mounting bracket to shim
(pre-installed inside header tube) with
appropriate fasteners.

Hex key size

4mm

3.4.2

Secure mag lock body to mounting bracket.

•

Insert mag lock body screws into slots in mounting bracket.

Mounting

bracket

Mounting

bracket

Shim

Mag loc

bod

3.4.3

Slide mag lock body
backward and into
place in slots.

3.4.4

Rethread captive
mounting screws.

3.4.5

Reinsert one (1)
anti-tamper screw.

NOTE: Other anti-tamper
screw to reinsert later. Access
needed to wiring cavity.

Slots in

mounting

bracket

Mag lock

body screws

Captive mounting

screws

Anti-tamper

screw

Header

tube

Shim

Header

tube

Mag lock

body

Wiring

cavity

Содержание EML 310






















Результаты поиска

Содержание EML 310

Отзывы:

Бренды по названию

Популярные бренды

Dormakaba EML 310, Руководство по установке

Результаты поиска

Содержание EML 310

Отзывы:

Бренды по названию

Популярные бренды