Dormakaba ED50LE страница 26 Скачать руководство пользователя

Страница: 26 / 50

ED50LE

09-2021

DL4616-002

dormakaba ED50LE operator – Fine cover
Installation Instructions

Chapter 8

Fig. 8.8.1 ED50LE operator mounting plate installation

ED50 mounting
plate

ED50 operator

Guide pin

115 Vac plug

Fig. 8.8.2 115Vac plug and socket

115 Vac plug

115 Vac socket

Power off/on switch

8.8.1 Install operator onto mounting plate.

CAUTION

Protective film strip removal.

Insure two protective film strips
have been removed from operator
heat conductive pads..

1. Slide ED50LE operator over the three

mounting plate guide pins and onto
mounting plate.

• Guide 115 Vac plug (4) into housing

adjacent to socket (6).

2. Thread the eight captive M6 SHCS (7)

into their mounting plate holes using
5 mm hex T-handle.

3. Tighten the eight M6 SHCS.

8.8.2 Insert 115 Vac plug into socket.

1. Insert 115 Vac plug from mounting plate

115 Vac terminal block into socket
(Fig. 8.8.2).

8.8.3 Full width cover option.

CAUTION

Program switch wiring.

Reference Appendix A for program
switch wiring terminal connections.

Accessory wiring
terminal connectors

115 Vac socket

M6 x 10 SHCS

8.8 Install ED50LE operator onto mounting plate

8.7 Remove protective film strips from operator

Heat conductive pad

Fig. 8.71 Operator heat conductive pads

8.7.1 Remove protective film strips.

1. Remove two protective film strips from

operator heat conductive pads.

CAUTION

Heat conductive pads.

Heat conductive pads must
remain clean once protective film
strips are removed!

Содержание ED50LE



















































Результаты поиска

Содержание ED50LE

Отзывы:

Похожие инструкции для ED50LE

Бренды по названию

Популярные бренды

Dormakaba ED50LE, Руководство по установке

Результаты поиска

Содержание ED50LE

Отзывы:

Похожие инструкции для ED50LE

Бренды по названию

Популярные бренды