Dorma ED400 страница 6 Скачать руководство пользователя

Страница: 6 / 26

DORMA

ED400 In Floor
Controller Manual

DORMA AUTOMATICS, Inc.

924

Sherwood

Drive

Toll-Free:

877-367-6211

DL3128-010

Lake

Bluff,

60044

Fax:

877-423-7999

10/1/2007

E-mail:

[email protected]

Subject to change without notice

SET-UP

User Interface

The controller user interface is quite intuitive.

It includes a display and two rotary switches

(knobs).

Use the top knob ("SELECTOR") to select the function.

Use the bottom knob
("DIAL") to change a setting.

The display shows letters using only 7-segments, so some letters may not be obvious.

MOUNT

OPN SPD

BCK CHK

BCK SPD

BCK STP

OPN DLY

CLS SPD

LCH CHK

MISC SEL

MISC ADJ

MONI SEL

MONITOR

LEARN

RUN TYPE

SELECT

DIAL

DISPLAY

Quick Start

In this quick-start we'll use only a few of the available menus. For a complete list of settings see
the

Menu Reference

section.

To adjust the opener, do the following (for an alternate procedure, see

"Set-up without

temporary stop"

in the Appendix):

•

Turn on the controller

•

Apply AC power to the controller.

•

The controller will light up.

•

Set the Program Switch in the "Off" position.

•

Indicate the door mount.

•

Turn the Selector knob to the position "Mount"

•

Turn the Dial knob to select

•

Prepare to teach the opener where you want Electrical Back-Stop to be.

•

If the operator has an internal hard-stopin the open position, set it to keep the

door from banging at the open end, and, at the sametime as wide as

possible, so that the door can reach the desired Back-Stop position (the

Electrical Back-Stop) without hitting the operator's hard stop.

•

Turn the "Selector" knob to the "Back-Stop" position. The display

should show "90", the programmed Back-Stop angle in degrees.

If not, or if you want the Electrical Back-Stop to be elsewhere,

change it with the Dial knob. Get ready to stop the door, such

as with your foot, at the desired Electrical Back-Stop.

•

Do a learn cycle.

•

Turn the "Selector" knob to the "Learn" position. The

display shows the Learn State. If it doesn't say "ALL"

(meaning it needs a full learn), turn the "Dial" knob

counter-clockwise

until

does.

MOUNT

DIAL

BACK-STOP

DIAL

LEARN

Содержание ED400



























Результаты поиска

Содержание ED400

Отзывы:

Похожие инструкции для ED400

Бренды по названию

Популярные бренды

Dorma ED400, Руководство по установке

Результаты поиска

Содержание ED400

Отзывы:

Похожие инструкции для ED400

Бренды по названию

Популярные бренды