Doosan 10/370 Скачать руководство пользователя страница 51

Страница: 51 / 96

Operating Instructions

Operating & Maintenance Manual

4. Insure that pressure is maintained at rated pressure, then turn regulator

adjustment screw (H) counter clockwise until engine speed just begins to be
reduced.

NOTE: Turning regulator adjustment screw (H) clockwise will raise
pressure at full speed.

5. Close service valve (engine will slow to no load or idle speed).

6. If necessary, repeat steps 3 and 4.

7. At pressure regulator (PR) tighten lock nut (G).

8. To adjust the unloaded pressure to any pressure between 80 psi (550 kPa) and

the rated operating pressure, turn adjustment screw (H) of pressure regulator
(PR) to obtain desired discharge pressure at full load engine speed. Always
lock and protect pressure setting of adjusting screw (H) with locknut (G).

9. Ensure unloader solenoid (US) acts to hold pressure in inlet unloader (IU) after

shutdown. After start-up, the compressor controller will open unloader solenoid
(US).

Содержание 10/370

































































































Результаты поиска

Содержание 10/370

Отзывы:

Бренды по названию

Популярные бренды

Doosan 10/370, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание 10/370

Отзывы:

Бренды по названию

Популярные бренды