manualshive.com logo in svg

Doosan 10/370, Руководство по эксплуатации и обслуживанию

Поделиться
Скачать
Doosan 10/370 Скачать руководство пользователя страница 38

Operating & Maintenance Manual

Operating Instructions

38

  

Operating Instructions

Operating Controls and Instruments

The operating controls and instruments are arranged on the control panel as shown above. A 
description of each panel device is as follows:

1.

Panel Light:

 Illuminates instrument and control panel. Controlled by Switch 14.

2.

High Compressor Temp:

 Fault indicator lamp. Indicates shutdown due to high

compressor temperature.

3.

Low Radiator Coolant Level:

 Alarm indicator lamp. Indicates engine coolant

needs service.

4.

Low Engine Oil Pressure:

 Fault indicator lamp. Indicates shutdown due to low

engine oil pressure.

5.

Restricted Air Filter:

 Alarm indicator lamp. Indicates engine/compressor air

inlet filters need service.

6.

High Engine Coolant Temp:

 Fault indicator lamp. Indicates shutdown due to

high engine water temperature.

Содержание 10/370

































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды