DONPER BH7480 Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 38

DONPER BH7480 Скачать руководство пользователя страница 16

DONPER

USA

—USER MANUAL

16 — COPYRIGHT DONPER USA 2015

Adjus ng the Product Firmness Level: (cont’)

The recommended star ng se ng for the product

fi

rmness level is 5.

With your product in the machine for the

fi

rst me and the AUTO fea

‐

ture running, wait un l the display cycles from 0 to 99 and then shows
00. Dispense some of the product from the machine and check the con

‐

sistency/

fi

rmness. If a

fi

rmer product is desired, then increase the

fi

rm

‐

ness se ng by 1

‐

2 and allow the machine to recycle back to 00 again

and retest the

fi

rmness. Repeat this process un l the desired product

fi

rmness is reached.

As a guide to help determine the appropriate product

fi

rmness se ng,

the numbers on the display in AUTO mode should start at 0 and quickly
rise to about 84 to 87 when the product inside the freezing cylinders is in
a complete liquid state (for example, when the machine is

fi

rst

fi

lled with

fresh product and started a er cleaning). If the numbers rise above 87
to start, then increase the

fi

rmness se ng 1

‐

2 number values and re

‐

start the AUTO mode and observe if the numbers stop increasing rapidly
somewhere near 84

‐

87.

OPERATING IN THE STANDBY MODE:

During long non

‐

use periods, the machine can be placed in Standby

Mode in order to keep the product inside the freezing cylinders refriger

‐

ated.

«
...
14
15
16
17
18
...
»

Содержание BH7480







































Отзывы:

Нет отзывов