background image

PART 1:   INSTALLATION

 

1.1 Modifications: 

Any modification, change, or 

substitution of any fireplace component and/or 
not following the installation, operation, and 
maintenance instructions will void the warranty 
and can put your security at risk.

1.2 Installation instructions:

 Before installation 

begins, carefully read the manual and contact 
your local building department to determine 
whether a building permit is required to install a 
fireplace. 

1.

3  Applicable Codes: 

The installation must 

follow the instructions in this manual and local 
building codes. If there is a conflict, you must 
follow the more restrictive measures.

1.4   Professional Installation: 

For your security, 

enlist the services of a professional fireplace fitter 
for the installation.  

1.5 Before your first fire: 

Before lighting your 

first fire, read the  instructions in Part 2 regarding 
operating the fireplace.

1.6 Installation prohibited: DO NOT 
INSTALL THIS INSERT INTO A ZERO-
C L E A R A N C E   I N S U L A T E D  
PREFABRICATED FIREPLACE:  Your insert 
is designed to be installed only inside a 
traditional solid masonry fireplace. If it is 
installed in an insulated zero-clearance 
fireplace, the high temperatures produced by 
the insert can cause a fire.

1.7 Chimney damper: 

The existing chimney 

damper must be set permanently in the open 
position. 

 

 

 1.  Warnings and Cautions (con’t)

 

Page 5

Typical installation inside
an existing masonry fireplace 
(with a rigid liner)

Stainless steel
round top 
and flashing

Metal plate with 
insulation at
the damper level
to solidify the liner 
and make it airtight

Stainless
steel rigid
and/or flexible
liner into the
existing
chimney 

The existing 
ash shaft can 
be used with
a fan in the
basement
(optional)

Outside air intake
with insulated flexible
duct (optional)

Centrifugal fan

(optional)

Insulation

(for basement fan

airtightness)

Basement

DRAWING 1

Acoustical
case
(optional)

Rockwool

insulation

secured with

a steel sheet

(see art 3.3)

Fan thermodisc
(optional)

Anti-turbulence
deflector (curved
metal sheet)

Don-Bar
Insert

REV.  2014-11

Содержание Inserts



























Отзывы: