manualshive.com logo in svg

Domnick Hunter Maxigas 104, Руководство по обслуживанию

Поделиться
Скачать
Domnick Hunter Maxigas 104 Скачать руководство пользователя страница 3

 

EN 

 

 

 

 
 
 

CONTENTS 

 

1 Safety Information................................................................................................................................................................................................ 5

 

1.1

 

Markings and Symbols........................................................................................................................................................................... 6

 

2 TECHNICAL SPECIFICATION.............................................................................................................................................................................. 7

 

3 Menu Interface...................................................................................................................................................................................................... 9

 

ppm......................................................................................................................................................................................................................... 12

 

3 Servicing ............................................................................................................................................................................................................. 15

 

3.1 Cleaning....................................................................................................................................................................................................... 15

 

3.2 Service Intervals ......................................................................................................................................................................................... 15

 

3.3 Service Kits ................................................................................................................................................................................................. 16

 

3.4 Service Procedures .................................................................................................................................................................................... 17

 

3.4.1 Exhaust Silencer Replacement ............................................................................................................................................................. 18

 

3.4.2 Oxygen Sensor Replacement ............................................................................................................................................................... 18

 

3.4.3 Dust Filter Element Change .................................................................................................................................................................. 18

 

3.4.4 Outlet Flow valve replacement.............................................................................................................................................................. 19

 

3.4.5 Control Valve replacement.................................................................................................................................................................... 19

 

3.4.6 Inlet Valve Replacement ....................................................................................................................................................................... 20

 

3.4.7 Outlet Valve Replacement .................................................................................................................................................................... 21

 

3.4.8 Equalisation Valve Replacement .......................................................................................................................................................... 22

 

3.4.9 Exhaust Valve Replacement ................................................................................................................................................................. 23

 

3.5 Oxygen Analyser Calibration..................................................................................................................................................................... 24

 

4 Oxygen Analyser ................................................................................................................................................................................................ 25

 

E1 – Calibrate sensor..................................................................................................................................................................................... 26

 

E2 – Analogue output FSD ............................................................................................................................................................................ 26

 

E3 – Set 4 mA output ..................................................................................................................................................................................... 26

 

E4 – Set 20 mA output ................................................................................................................................................................................... 26

 

E5 – Sensor simulation .................................................................................................................................................................................. 27

 

E6 – Sensor selection .................................................................................................................................................................................... 27

 

E8 - Diagnostics ............................................................................................................................................................................................. 28

 

E9 - Restore ................................................................................................................................................................................................... 28

 

5 Troubleshooting ................................................................................................................................................................................................. 29

 

6 Service Record ................................................................................................................................................................................................... 31

 

APPENDIX A .......................................................................................................................................................................................................... 33

 

 

  

Содержание Maxigas 104





































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды