background image

30

GDO-7v2 

Owner Installation Instructions

Warranty and Exclusion of Liability

1.  This warranty is an addition to any non-excludable conditions or warranties that are implied into this contract 

by relevant statutes.

2.  Subject to all of the matters set out below, B&D Doors (NZ) Ltd (“B&D”) warrants:

  (a) overhead door opener drive units for twenty four (24) months or 5000 cycles, whichever occurs fi rst; and
  (b) all components and accessories for twelve (12) months, from the date of purchase (specifi ed in the sales 

docket receipt) as free of any defects in material and workmanship.

3.  This warranty applies only where the purchaser:

  (a) immediately notifi es BND or the retailer of the alleged defect;
  (b) returns the product to the retailer; and
  (c) presents the relevant sales docket and this warranty document to the retailer to confi rm the date 

of purchase.

4.  Except for this warranty, BND gives no warranties of any kind whatsoever (whether express or implied), 

in relation to the product, and all warranties of whatsoever kind relating to the product are, to the extent 
permissible by statute, hereby excluded. 

5.  To the extent permissible by statute, BND disclaims any liability of whatsoever nature in respect of any claim 

or demand for loss or damage which arises out of:

  (a) accidental damage to or normal wear and tear to the product or to the product’s components;
  (b) any cost relating to damage resulting from wear and tear;
  (c) blown fuses, loss or damage caused by electrical surges, power surges or power spikes;
  (d) loss or damage due to theft, fi re, fl ood, rain, water, lightning, storms or any other acts of God;
  (e) maximum continuous operating time exceeding one (1) minute in ten (10);
  (f) maximum operating force exceeding *20kg (200N) when moving the door manually to the open or closed 

position;

  (g) door surface area and/or weight exceeding 16.5m

2

 and 100kg respectively;

  (h) door not in safe and correct working order and condition;
  (i) evidence of unauthorised repairs;
  (j) any cost relating to damage caused by misuse, negligence or failure to maintain the equipment in a 

proper working order as per clauses (d) through (h);

  (k) installation, adjustment or use which is not in accordance with the instructions set out in installation 

instruction manual

  (l) attempted or complete modifi cation or repairs to the product carried out by a person who is not 

authorised or has not been trained by BND to carry out such modifi cation or repairs;

  (m) faulty or unsuitable wiring of structure to which the product is fi xed or connected;
  (n) radio (including citizen band transmission) or any electrical interference;
  (o) damage caused by insects;
  (p) loss or damage to any property whatsoever or any loss or expense whatsoever resulting or arising there 

from or any consequential loss;

  (q) any cost or expense arising due to manufacturer recall of any product;
  (r) any cost or expense due to negligence of the approved service provider;
  (s) installation of a residential garage door opener in a commercial or industrial situation or a non-single 

residential dwelling.

6.  BND’s liability under this warranty is limited, at BND’s absolute option, to replacing or repairing the product 

which BND, in its unfettered opinion, considers to be defective either in material and/or workmanship or to 
credit the dealer with the price at which the product was purchased by the dealer. 

7.  This warranty does not extend to cover labour for installation. 
8.  This warranty is limited to Return-to-Base (RTB) repair and does not cover labour for on-site attendance. 
9.  This warranty is void if the Product is not returned to the manufacturer in original or suitably secure packaging. 
10.  This warranty is only applicable for repairs to the product carried out within Australia.
11.  This warranty does not cover consumable items including globes, batteries and fuses.
12.  This warranty is not transferable.
13.  Where the Product is retailed by any person other than BND, except for the warranty set out above, such 

person has no authority from BND to give any warranty or guarantee on BND’s behalf in addition to the 
warranty set out above. 

NOTES:

1. One (1) cycle = one (1) open and one (1) close action of the door or gate.
2. This warranty is to be read in conjunction with the owner’s copy of the installation instruction manual.
3 *The door should be balanced in such a way that the user manually is able to open or close the door without using 

force not greater than 150N (15kg ) although a greater force may be required for the start of the movement.

Содержание GDO-7v2

































Отзывы: