background image

• MAKE SURE YOU HAVE ENOUGH SPACE AND SUPPORT.

– Mount the oven against a flat, vertical wall, so it is supported by the wall. The wall should be constructed

to support 150 lbs.

– ATTACH AT LEAST ONE of the two lag screws supporting the oven to a vertical, frame member.

– DO NOT mount the microwave oven to an island or peninsula cabinet.

– BE SURE the upper cabinet and rear wall structures are able to support 150 lbs., plus the weight of any

items you place inside the oven or upper cabinet.

– Locate the oven away from strong draft areas, such as windows, doors, and strong heating vents.

– BE SURE you have enough space. See Figure 4 below for minimum vertical and horizontal clearance.

If you do not mount the oven as instructed,

you risk personal injury and/or property damage.

C  A  U  T  I  O  N

• Before you begin installing the oven, PLACE A PIECE OF THE CARTON OR OTHER HEAVY

MATERIAL (a blanket) over the countertop or cooktop to protect it. Do not use a plastic cover.
Failure to protect these surfaces could result in property damage.

YOUR SAFETY FIRST

30" min. cabinet opening width

30" min. clearance from bottom
of cabinet to cooking surface
or countertop

(Use templates included
 with installation instructions)

Grounded Outlet
(inside upper cabinet)

Power Supply Cord Hole

Figure 4

W A R N I N G

– 4 –

Содержание DOTRM13B



















Отзывы: