background image

PXH842 User’s Guide –

 Dolphin Interconnect Solutions 

 

 

 

 

 

 Page 11 

Firmware upgrade 

The PXH842 card uses a microcontroller to implement configuration, management and maintenance functions. Dolphin may from 
time to time publish updated firmware for the microcontroller or EEPROM data for the card.  Please note that standard PLX 
firmware tools cannot be used to upgrade the firmware. Please contact Dolphin for more information. 

 

Identifying the Card 

The card has a label-

sticker with the serial number in the format ‘

PXH842-YY-

ZZZZZZ’, where YY denotes the card revision (

e.g. CC) 

and ZZZZZZ denotes the serialized production number (e.g. 012345) 

 this whole string makes up the serial number of the card (i.e. 

PXH842-CC-012345). 

You can also get this information using lspci in Linux: 

First, identify the devices for the Dolphin Host card: 

 

 

 

 

Than run lspci, and identify the card. It will show up as something like 

 
 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Second, do  

 
 
 
 
 
 

This shows the card as revision 0x4243 (hexadecimal values of the ‘CC’ letters in the 

ASCII table), with the production number 

0x0000000A (0000010 in decimal). 

# lspci -s 1:0.0 -v  
01:00.0 PCI bridge: PLX Technology, Inc. Device 8733 (rev ca) (prog-if 00 [Normal decode])  
Flags: bus master, fast devsel, latency 0, IRQ 25  
Memory at f7d00000 (32-bit, non-prefetchable) [size=256K]  
Bus: primary=01, secondary=02, subordinate=03, sec-latency=0  
Capabilities: [40] Power Management version 3  
Capabilities: [48] MSI:  Count=1/8 M 64bit+  
Capabilities: [68] Express Upstream Port, MSI 00  
Capabilities: [a4] Subsystem: Dolphin Interconnect Solutions AS Device 0832  
Capabilities: [100] Device Serial Number 00-00-43-43-00-00-00-0a  
Capabilities: [fb4] Advanced Error Reporting  
Capabilities: [138] Power Budgeting <?>  
Capabilities: [10c] #19  
Capabilities: [148] Virtual Channel  
Capabilities: [e00] #12  
Capabilities: [b00] Latency Tolerance Reporting  
Capabilities: [b70] Vendor Specific Information: ID=0001 Rev=0 Len=010  
Kernel driver in use: pcieport  
Kernel modules: shpchp 

# lspci | grep “Device 8733”

 

01:00.0 PCI bridge: PLX Technology, Inc. Device 8733 (rev ca)  
02:08.0 PCI bridge: PLX Technology, Inc. Device 8733 (rev ca) 

 

# lspci -s 1:0.0 -v | grep -E "Subsystem|Serial"  
        Capabilities: [a4] Subsystem: Dolphin Interconnect Solutions AS Device 0832  
        Capabilities: [100] Device Serial Number 00-00-43-43-00-00-00-0a 

 

Содержание PXH84 Series
















Отзывы: