Dolmar EM-461 S, Оригинальное руководство пользователя

Страница: 11 / 21

11
4. TECHNICAL DATA
5. ASSEMBLY
5-1 ASSEMBLE THE FOLDING HANDLE
1. Fix the lower handlebar onto the handle bracket with
bolt, washer and locking knob. (Fig. 3)
2. Lift the two locking levers to connect the upper and
lower handle. (Fig. 4)
3. Push the locking lever closed to lock the handlebars in
the operating position. (Fig. 5)
4. Adjust the tension by turning the lock nut with a
suitable spanner. (Fig. 6)
5. Position the cable over the handle shaft. Clamp it
around the middle of lower handle by the cable clamp
and make sure the cable is fixed around the outside of
the handle.
(Fig. 7) Otherwise the cable may be
pinched by opening/closing the rear cover.
5-2 ASSEMBLE THE GRASS CATCHER
1. To fit: Raise the rear cover and hitch the grass catcher
on rear of mower. (Fig. 8, Fig. 9, Fig. 10)
2. To remove: Grasp and lift the rear cover, remove
grass catcher.
GRASS CATCHER
There is a level indicator on the top of the grass catcher
that shows whether the catcher is empty or full
(Fig. 11,
Fig. 12) :
- The level indicator inflates if the catcher is not full during
the moving. (Fig. 12)
- If the catcher is full, the indicator collapses. Once this
happens, stop moving immediately and empty the
catcher, make sure it is clean and ensure its meshwork
is ventilated.
(Fig. 11)
IMPORTANT
If the position of indicator opening is very dirty, the
indicator will not inflate. In this case, clean the position of
indicator opening immediately.
6. ADJUSTMENT OF CUTTING
HEIGHT
Apply outward pressure to disengage lever from rack.
Move lever forward or back to adjust height.
The height (the blade to the ground) can be adjusted from
20 mm (the lowest position) to 75 mm (the highest
position), 8 height positions.
(Fig. 13)
WARNING: Make this adjustment only when the
blade is stopped.
WARNING: Disconnect the electric cord from the
power supply.
7. ADJUSTMENT FOR AN
APPROPRIATE ANGLE
a) Pull the locking lever opening.
b) Rotating the upper handle centered of the angle
adjusting gear for adjusting an appropriate angle into
the scope -15º to 15º (3 position: -15º/0º/15º) as the
Fig. 14 shown.
c) Push the locking lever closed to connect the lower
handle and the upper handle.
8. FUNCTION
These lawn mowers can be retrofitted from its normal
function, based on the application purpose.
From lawn mower with rear collection to:
Mulching mower or as
Side-discharge mower.
What is mulching?
When mulching, the grass is cut in one working step, then
finely chopped and returned to the grass strip as natural
fertilizer.
Model: EM-461 EM-461 S
Rated voltage: 230 V~ 230 V~
Rated frequency: 50 Hz 50 Hz
Rated power: 1,800 W 1,800 W
No load speed: 2,900/min 2,900/min
Cutting width: 460 mm 460 mm
Grass catcher capacity: 60 L 60 L
Net weight: 29.5 kg 32.5 kg
Degree of protection against liquid: IPX4 IPX4
Height adjustment: 20-75 mm, 8 adjustment 20-75 mm, 8 adjustment
EM-461 EM-461 S
Sound pressure level at operator’s
position
78.9 dB (A) K=3 dB (A) 78.9 dB (A) K=3 dB (A)
Measured sound power level 91.6 dB (A) K=1.94 dB (A) 91.6 dB (A) K=1.94 dB (A)
Guaranteed sound power level 96 dB (A) 96 dB (A)
Vibration 1.132 m/s 2
K=1.5 m/s
2
1.132 m/s
2
K=1.5 m/s
2